background image

13

Safety Instructions

An electric skateboard is not a toy, and should be treated with appropriate care. Always practice safety
first as it is possible to lose balance and cause a collision or fall, ensure that you use the board in a safe
appropriate environment, and you always wear appropriate safety gear.

Safety Gear - we recommend that you wear full safety gear when riding. Please wear a suitable skateboard
helmet, elbow pads, knee pads, and gloves. Wear suitable attire when skateboarding to protect you from
scrapes if you fall. Wear shoes - flipflops or similar loose footwear are not suitable riding wear.

The board is designed for use by responsible riders of the ages 13 and up.

Only one person can ride a Skateboard at a time

The maximum carrying weight supported by the boards is 60kg/130lbs. Exceeding this weight will affect
the skateboard balance and functionality, and may cause the board to fail, act inappropriately or
otherwise break.

Please observe your local traffic laws and regulations.

The board is designed to be ridden on flat and paved surfaces. Avoid driving on sand, gravel, mud,
rugged or open ground. Do not drive on slippery ground, such as snow, ice or wet ground.

Summary of Contents for SkyboardMini
















Reviews: