3
English - Installation manual
You have just acquired an
AXS2
uninterruptible power unit by SLAT, and we thank you for your choice.
In this manual, you will find all the instructions you need to install it.
For proper functioning of the unit, we recommend that these instructions be followed very carefully.
Safety precautions
AXS2 is an emergency power supply designed to be connected to the public distribution 230V network. It
ensures continuity of service for equipment in case of power failure. You can find more information in the
datasheet for download on our website www.slat.com
•
To avoid any risk of electric shock, all
INTERVENTIONS
must be carried out with the equipment
SWITCHED OFF
(upstream two-pole circuit-breaker open).
•
Interventions with the equipment switched on are authorized only when it is impossible to switch the
equipment off. The operation must only be performed by qualified personnel.
•
During installation, connect the ground wire first and disconnect it last when dismantling.
•
Mount the appliance in a vertical position.
•
Provide sufficient convection (top / bottom clearance minimum 30mm)
•
Size and protect cables defined according to the maximum current input / output (>0.2mm²/A).
•
Observe the thermal and mechanical limits.
•
The battery is maintenance-free. Do not open it.
•
Attention, there is a blast hazard if the battery is replaced with a wrong battery type!
•
Scrap the used batteries according to the directives
•
Indoor use only
•
Clean the cabinet with a soft rag.
Environment and public health protection standards and directives
Complies with EN 60950 -1 SELV class; EN 61000-6-1; EN 61000-6-2; EN 61000-6-3; EN 61000-6-4;
55022 + A1 Class B; EN 50131-6 Grade 2 for versions of the appliance in cabinets with a wall removal
contact and cover opening.
At the end of life, the product must be recycled. SLAT recycles its products at end of life.
Associated batteries
-
recombination-type lead, capacity depending on charger ratings: 1.2Ah; 2.1Ah; 7Ah; 12Ah; 17Ah; 24Ah;
40Ah
-
floating recharge at C/10
-
the battery jumper cables are fitted with connectors according to each associated battery
Environmental specifications
-
operating temperature: - 5°C to 50°C
-
storage temperature: - 25 to + 85°C
-
operating relative humidity: 20 to 95%
Electrical input specifications
-
single-phase voltage: 230V (195V-264V)
-
frequency: 50-60Hz (from 45 to 65Hz)
-
neutral systems: TT, TN, IT
-
a D curve circuit breaker with easy access to be provided upstream
-
primary current @230V:
0.25A
(12V 2A - 24V 1A);
0.75A
(12V 5A - 24V 2.5A);
1A
(12V 10A - 24V 5A)
Electrical output specifications
-
"floating" load output in relation to the ground.
-
float voltage:
13.6V
(12V 2A - 12V 5A - 12V 10A);
27.2V
(24V 1A - 24V 2.5A
– 24V 5A)
-
current limitation:
1A
(24V 1A);
2A
(12V 2A);
2.5A
(24V 2.5A);
5A
(12V 5A
– 24V 5A);
10A
(12V 10A)
Alarm reports
-
2 dry contacts (open when faulty) 1A@24Vdc, 0.5A@120Vac :
o
mains fault or rectifier fault
o
battery low voltage fault
-
Indicated by a LED on the front panel
