OPTIC REPLACEMENT:
Replacing optics requires the use of the plastic optic removal
tool (part# SBMLTOOL) which can be purchased seperately
and is provided free (one per case of six fixtures). For best
results, use a 9/16 or 14mm socket or a 5/16 allen key to
provide the handle/leverage required to remove the lock
ring holding the convex lens to the fixture body. It is best to
perform this on a clean will-lit surface free of moisture and
dirt.
Step #1–Seperate the light engine/shroud from fixture body
by loosening thumb screw.
Step #2–Grabbing the top and base of the white quick
connect, located in the top knuckle and attached to the
light engine/shroud wire, gently work the connection apart.
Do NOT yank wires as this might damage the connection.
Using a flat head screwdriver or your finger to hold the base
wire quick connect, gently wiggle the connection apart; use
needle nose pliers if required.
Step #3–Clean dirt, water, and/or leaves debris from convex
glass lens. Use compressed air or a brush to remove fine
particulate from lens.
Step #4–Place light engine/shroud on a flat surface. Hold
light engine/shroud with one hand, place two male optic
removal tool tabs in mating female tabs of lock ring and turn
counter clockwise loosening lock ring.
Step #5–Remove lock ring and remove convex glass lens and
white combination o-ring gasket seal.
Step #6–Remove optic and replace with new optic, making
sure the writing on the optic indicating beam angle is pointing
forward and visible. If dirt or debris fall into optic chamber,
use compressed canned moisture free gas to clear dirt from
chamber. Do not damage LED.
Step #7–Replace o-ring gasket seal making sure o-ring
side of gasket nests in groove of fixture body, replace
glass convex lens, replace lock ring. Using lock ring tool
and socket, turn clockwise to compress assembly making
watertight seal.
Step #8–Reattach light engine shroud to fixture body.
Source SBML Series: Multi Lumen Spotlight with Field Changeable Optics
Voltage Range 12V - 15V AC/DC Actual Results May Vary + or - 5%
LIGHT OUTPUT LUMENS / BEAM SPREAD
Finished Good Model # SBML15 SBML24 SBML36 SBML60 SBML80
Halgen
Equiva-
lent
Power
Seting
Voltage
Input
Current
/Amps
Input
Consumed
Wattage
Power
Factor
15
°
24
°
36
°
60
°
80
°
WASH
CCT
CRI
35W
#4, 4.2W 12.0 VAC
0.452 A
3.02
0.784
260 Lm
255 Lm
250 Lm
215 Lm
210 Lm
2800
°
K
85
30W
#3, 3.0W 12.0 VAC
0.329 A
2.25
0.767
200 Lm
195 Lm
190 Lm
163 Lm
160 Lm
2800
°
K
85
20W
#2, 2.0W 12.0 VAC
0.216 A
1.5
0.748
138 Lm
135 Lm
130 Lm
130 Lm
128 Lm
2800
°
K
85
10W
#1, 1.0W
12.0 VAC
0.120 A
0.77
0.722
86 Lm
85 Lm
80 Lm
70 Lm
68 Lm
2800
°
K
85
Replaceable Optic Part #
(Requires #SBMLTOOL, 1 piece included per 6 case.)
SMLO15 SMLO24 SMLO36 SMLO60 SMLO80
For Questions on how to obtain the proper cable or connectors, call (973) 423-2303 | www.cast-lighting.com
OPTIC REPLACEMENT
Optic Removal Tool
5/16 Allen Key or 9/16,
14mm Socket
Lock Ring
Replaceable Optic
15°, 24°, 36°, 60°, 80° Beam Angles
Lens
Gasket
