SleepSafe Beds Electric HiLo Combo FOUNDATION SleepSafe Assembly & Product Manual Download

Page: 15 / 20

Final Bed Installation Checklist







Check all bolts to see

that they are tight.

Be sure all fasteners that hold
the components are hand
tightened with wrenchs.

Check Safety Rails to

be sure they operate

and latch properly.

Safety Rails should pivot
correctly, align properly and
securely latch into the gate
located on the bed posts.

Latch Lever

Latch Pin

Allen and Torx Wrenchs
are included with the bed
delivery.

Check fit between

headboard, footboard,

bed sides and mattress.

The mattress should always fit
snugly against the sides. If not,
contact the DME or Customer
Service at SleepSafe Beds.

Check Bed Operation

with the Remote.

The Electric HiLo Combo should
move about 70° for the head
and about 35° for the knee. The
HiLo range is 10” up and down.
Test these features thoroughly.

For Extensions, check

operation of Safety

Latch holding the top

Safety Rail.

Top Safety Rail should set in
place when lifted up and into
place on the Extension.

Latch Gate

Mattress should

fit ¼” or less

on all sides.

Head should

move up to 70°

Knee should

move up to 35°

Foundation should

move up and down 10”

This latch should

be properly

mounted to the

Extension to

ensure top Safety

Rail is securely

held in place.

Thumb

operated

latch.

Top Safety

Rail

Summary of Contents for Electric HiLo Combo FOUNDATION SleepSafe





















Search results

Summary of Contents for Electric HiLo Combo FOUNDATION SleepSafe

Reviews:

Related manuals for Electric HiLo Combo FOUNDATION SleepSafe

Brands by name

Popular brands

SleepSafe Beds Electric HiLo Combo FOUNDATION SleepSafe, Assembly & Product Manual

Search results

Summary of Contents for Electric HiLo Combo FOUNDATION SleepSafe

Reviews:

Related manuals for Electric HiLo Combo FOUNDATION SleepSafe

Brands by name

Popular brands