SleepSafe Beds SleepSafe II Product Assembly Manual Download

Page: 12 / 20

Up and Down Safety Rail Adjustment







Side by Side Safety Rail Adjustment





Does the Safety Rail

need adjustment?

For proper operation the pin
should be centered in the strike.
If not centered, follow the following
steps to center the pin in the strike.

PULL

LEVER

STRIKE

Additional Tools Needed:

Hammer or Mallet

Portable Electric Drill

Remove Strike

from Bed Post.

Use Drill with Torx bit to remove
screws from the Strike. Gently tap
the strike out of the bed post with
hammer or mallet to access

POST

Adjust Set Screw.

Use Torx 10 wrench to adjust set
screw. Keep in mind which direction
that you need to adjust the pin.
If the pin needs to be raised, turn
the set screw clockwise. If the pin
needs to be lowered, turn the set
counter-clockwise.

To RAISE pin, turn
Clockwise
To LOWER pin, turn
Counterclockwise

Reinsert Strike into Bed Post.

Check to see if the Pins are centered properly within the Strikes.

Use Portable Drill with Torx
bit to remove screws holding
Strike to bed post,

Does the Safety Rail

need adjustment?

When up and secure, check the spacing
between the end of the safety rail and
the headboard and footboard legs.
They should be spaced evenly.

Remove Safety Rail

and adjust the play.

If spacing is not even, or there is
too much side-to-side play in the rail,
turn the black hex bolt using the ¼”
Allen Wrench provided .

This spacing should be even

on both sides.

To INCREASE play
turn bolt
CLOCKWISE

To DECREASE play
turn bolt
COUNTERCLOCKWISE

MANUAL ELECTRIC COMBO

SleepSafeBed.com

1-866-852-2337

3629 Reed Creek Dr. | Bassett, VA 24055

Summary of Contents for SleepSafe II





















Search results

Summary of Contents for SleepSafe II

Reviews:

Related manuals for SleepSafe II

Brands by name

Popular brands

SleepSafe Beds SleepSafe II, Product Assembly Manual

Search results

Summary of Contents for SleepSafe II

Reviews:

Related manuals for SleepSafe II

Brands by name

Popular brands