background image

 
2. Install the propeller and spinner. Gasoline engines are very powerful and can 

cause damage to persons or property if propellers and spinners are not installed 
properly. Follow the manufacturer's instructions and make sure your propellers 
are well balanced, properly drilled, and display no cracks or chips.

HORIZONTAL STABILIZER AND ELEVATOR CONTROLS ASSEMBLY:

1. Locate the one piece stabilizer. Slide it in the stabilizer cutout in the back of the 

fuselage and center it. To ensure squareness of the assembly, measure the 
distance of the trailing tip of the wing to the trailing tip of the stabilizer on both 
sides. Make sure that they are equal. Once this is done, mark the area where the 
stabilizer meets the fuselage with a fine marker. Remove the stabilizer from the 
fuselage and carefully cut the covering off.

2. Locate the elevator couplers and prepare to place it in the fuselage along with 

the stabilizer.

3. Prepare some 30 minute epoxy. Have some paper towels soaked in isopropyl 

alcohol to wipe off the excess epoxy. Apply the epoxy over the expose area of 
the stabilizer and reinstall the stabilizer onto the fuselage. Wipe off the excess 
epoxy. Redo the measurement to ensure the squareness and center of the 
stabilizer. Set it aside and let to allow the glue to dry.

4. Locate and prepare the CA-hinges for installing the elevators onto the stabilizer. 

Ensure that the two halves travel equally when using the elevator coupler. Once 
all is checked for correctness, harden the holes where the coupler inserts into 
the elevator with thin CA to harden the wood.  Employ the same method that was 
used to install the rudder. 

5. Locate the pushrod and install it in the same manner as was installed in the 

rudder.

WING AND AILERON CONTROLS ASSEMBLY:

1. Locate the 3 pieces of the wing and joiners.

Summary of Contents for 30CC BEAVER













Reviews: