background image

8

SLS™ MA390C Installation Guide

Environmental Compliance and Regulations

 

EU Environmental Regulations and Compliance

Following

 

are

 

the

 

MA390C

 

EU

 

environmental

 

regulations

 

and

 

compliance

 

information.

 

Waste Electrical and Electronic Equipment (WEEE)

 

All

 

Dolby

 

products,

 

which

 

must

 

be

 

recycled

 

or

 

handled

 

separately,

 

are

 

marked

 

with

 

this

 

WEEE

 

label

 

in

 

accordance

 

with

 

the

 

EU

 

WEEE

 

Directive.

Restriction of Hazardous Substances Directive (RoHS)

All

 

Dolby

 

products

 

comply

 

with

 

the

 

requirements

 

of

 

the

 

EU

 

RoHS

 

Directive.

 

For

 

the

 

Dolby

 

Declarations

 

of

 

Conformity,

 

go

 

to

 

http://www.dolby.com/us/en/about/environmental-commitment.html

.

Product End-of-Life Information

This

 

product

 

has

 

been

 

designed

 

and

 

built

 

by

 

Dolby

 

Laboratories

 

to

 

provide

 

many

 

years

 

of

 

service,

 

and

 

is

 

backed

 

by

 

our

 

commitment

 

to

 

provide

 

high

quality

 

support.

 

When

 

the

 

product

 

eventually

 

reaches

 

the

 

end

 

of

 

its

 

serviceable

 

life,

 

it

 

should

 

be

 

disposed

 

of

 

in

 

accordance

 

with

 

local

 

or

 

national

 

legislation.

 

For

 

information

 

regarding

 

disposal,

 

go

 

to

 

http://www.dolby.com/us/en/about/environmental-commitment.html

.

Summary of Contents for MA390C















Reviews: