1. Use as directed:
This product serves exclusively lighting purposes and may:
only be operated using a suitable
conventional transformer
, output:
12V~50-60Hz
.
not be exposed to strong mechanical loads or to strong contamination.
only be installed and operated after a condition inspection if the product
is dirty or has been moistened through storage.
not be modified or converted.
If these points named above are not adhered to, a short circuit or
electrical shock may occur!
2. Technical Data:
Operating voltage:
12V~50-60Hz
Safety class:
III
Safety type:
IP 67
Bulb:
9 x SMD LED
Power :
1W
Dimensions (Ø/H):
8 / 1,6 cm
Weight:
0,25 kg
Importeur: SLV
Elektronik
GmbH
IP 67
: Protection against dust(dust-tight) - Protection against the
penetration of water when temporarily submerged.
3. Installation
The complete installation must be done by an electrical expert,
who is familiar with the valid directives.
Attention: Switch off power of the mains supply or respectively of
the connection lead before doing any works.
Use only parts, which are supplied with the product or are described as
accessories! Otherwise the product or the installation might not be
sufficiently safe!
Indication for the installer
: In case you do not install a completely
supplied system (with transformer), you are considered a "manufacturer" by
the low-voltage directive. In this case you are required to ensure the
conformity of the whole system and declare it by attaching the
CE-sign
.
Installation place:
The product is suited for
wall and floor installation
.
Make sure that the product is mounted on a
stable, even and tilt-fixed
background
.
Preparing the low-voltage(12 V) power supply
The transformer should be used up to 80 % of its capacity. The total watt
power of the connected light fittings must not exceed the power output of
the transformer. The distance between spot and transformer should be at
least 20 cm. Note the manufacturers information for the transformer.
High currents with low-voltage installations!
Use only heat resistant
wires and clamps to avoid danger of fire.
Check all electrical connections
once in a while for a secure fit.
Operate SKY PLOT only with a conventionel transformer!
Separate Installation Steps
Mount the transformer, according to the manufacturers instructions, at
the desired place and prepare the 12V supply lead. To grant the
protection code
IP 67
an outdoor connection box with the same or a
higher IP class must be utilized.
Use a blank tube to lay out the leads.
Connect the product with the prepared low-voltage power supply.
Fix the lamp firmly on the ground
The product is now ready for operation.
4. Operation
:
Information for the user:
Operate the product only if it is working correctly. Switch off the product
with a malfunction immediately and operate it again only after examination
by an electrical specialist. This is the case, when:
visible damages appear.
the product does not work.
smoke, steam or crackling sounds appear.
an overheating is recognisable.
Repairs of the product or work on mains voltage-prominent sections may
only be carried out by qualified electricians.
Attention:
Here exists mortal danger from an electric shock!
How to avoid failure and fire risk:
Do not cover the product - provide free air circulation!
Do not hang or fasten anything on the product, especially no decoration.
Never let children play unsupervised with electric products! Children
can not always estimate dangers in dealing with electric energy correctly.
The following enviromental influences may have unwanted effects on
the surface of the product:
acid rain and sour soil
high salt content in the air
thawing salt
cleaning agents
other chemical substances (e.g. herbicides)
Protect the product by adequate means to avoid unwanted changes of the
surface.
Cleaning tip
: Switch off power! Clean the product with a damp
cloth.
What is to do if a bulb is defect or does not work?
Under regular usage the LED bulb has an extraordinary long lifetime. If
nevertheless damage or failure occurs, contact your local dealer to
exchange the LED bulb.
5. What else has to be considered?
Disconnect the product from power, before you…
clean or maintain the product.
do any works on the product or its components (electric expert).
Art.-Nr. 227391/92/97 05/2007
©
by SLV Elektronik GmbH
Technical Details are subject to change.
Duplication prohibited !
ENGLISH
Instruction Manual
for
LED Light
SKY PLOT
Please read carefully and keep for further reference !
