Slycma ARIANE 3.1 Commissioning Manual Download

Page: 4 / 34

Ref : 26702 4 07/01/15

CONTENTS

PART 1 : Connection of the ARIANE 3.1 card

Mains power connection ........................................................... Page 5

Asynchronous motor connection ............................................... Page 5

Brushless motor connection ..................................................... Page 5

Encoder connection ................................................................. Page 6

Safety chain connection ........................................................... Page 6

Controller orders connection ...................................................... Page 6

Car input cell connection .......................................................... Page 7

Controller signals connection .................................................... Page 7

Multifunction relay connection .................................................. Page 8

Wire function terminals list ...................................................... Page 8

PART 2 : Configuration according to the controller

Setting of mandatory parameters .............................................. Page 9

Details about the configuration parameters ............................... Page 10

PART 3 : Commissioning the ARIANE 3.1 card

Mechanical efficiency checking ................................................. Page 13

Travel learning ...................................................................... Page 13

PART 4 : Adjustment of the door operation

Operating diagrams ............................................................... Page 14

Changing a parameter ............................................................ Page 14

Operating values ................................................................... Page 15

Value range table .................................................................. Page 16

PART 5 : Saving the parameters

Saving the parameters ........................................................... Page 17

Recording your own parameters ............................................... Page 18

PART 6 : Details about the command modes (CMD)

The command modes (CMD) ................................................... Page 19

Special case of a double opening travel ..................................... Page 20

PART 7 : Details about the ARIANE 3.1 operations

Basic operation .................................................................... Page 21

Reset operation ..................................................................... Page 22

Inspection operation .............................................................. Page 22

Parameterizable relays operation .............................................. Page 23

Fail soft operation .................................................................. Page 24

Operation with Car door locking device ..................................... Page 24

Energy save operation ............................................................ Page 24

PART 8 : Maintenance operations

Card Inputs/Outputs display .................................................... Page 25

Operating faults display .......................................................... Page 26

Details about operating faults .................................................. Page 27

Encoder position display ......................................................... Page 28

Numbers of cycles display ....................................................... Page 28

Summary of Contents for ARIANE 3.1



































Search results

Summary of Contents for ARIANE 3.1

Reviews:

Related manuals for ARIANE 3.1

Brands by name

Popular brands

Slycma ARIANE 3.1, Commissioning Manual

Search results

Summary of Contents for ARIANE 3.1

Reviews:

Related manuals for ARIANE 3.1

Brands by name

Popular brands