Medi-Minder Installation Manual Rev1.11
15
Pabx Tones
Enabled - Unit will automatically hang up if it detects a specific hang up signal (ie. short beep, long gap)
Disabled - Medi-Minder unit will not detect a hang up so call needs to be either, manually terminated
(Pressing the * Key twice), pressing the Medi-Minder unit CANCEL (Green) Button (or the OFF
Button on any 3 Button Pendant), or by waiting for the Medi-Minder unit to time out.
NB: “IF RUNNING ON A PABX SYSTEM, THIS OPTION SHOULD ALWAYS BE DISABLED.”
1.
“
Pb
” is displayed. Press the HELP Button to view programmed option.
2.
“
E
” is displayed. Pressing the HELP Button again toggles between “
E
” Enabled and “
d
” Disabled.
3.
To store an option selected, press the CANCEL and HELP Buttons at the same time. The unit will beep
twice while flashing the display to acknowledge that the option has been selected. Press the CANCEL
Button to move to the next Program Option.
Rings Detected
2 to 9 Number of Rings to detect before automatically answering after an alarm event.
1.
“
rd
” is displayed. Press the HELP Button to view programmed Number of Rings.
2.
“
2
” is displayed. Pressing the HELP Button again to step through digits (
2, 3, 4, 5, 6, 7, 8,
or
9
Rings).
3.
To store an option selected, press the CANCEL and HELP Buttons at the same time. The unit will beep
twice while flashing the display to acknowledge that the option has been selected. Press the CANCEL
Button to move to the next Program Option.
Country Dialing
AUSTRALIA (Force DTMF)
NEW ZEALAND
SINGAPORE, USA & CANADA
UK & EUROPE
1.
“
Co
” is displayed. Press the HELP to view programmed option.
2.
“
1
” is displayed. Pressing the HELP Button again to step through
1, 2, 3
&
4
.
3.
To store an option selected, press the CANCEL and HELP Buttons at the same time. The unit will beep
twice while flashing the display to acknowledge that the option has been selected. Press the CANCEL
Button to move to the next Program Option.
Up/Download & Remote DTMF Control
Enabled all the time and DTMF Enabled
Enabled only in Program Mode and DTMF Enabled
Enabled all the time and DTMF Disabled
Enabled only in Program Mode and DTMF Disabled
1.
“
ud
” is displayed. Press the HELP Button to view programmed option.
2.
“
1
” is displayed. Pressing the HELP Button again to step through
0, 1, 2,
&
3
.
3.
To store an option selected, press the CANCEL and HELP Buttons at the same time. The unit will beep
twice while flashing the display to acknowledge that the option has been selected. Press the CANCEL
Button to move to the next Program Option.
RS232 Baud Rate
0 = Disabled, 1 = 9600, 2 = 19200, 3 = 38400, 4 = 57600 & 5 = 115200
1.
“
rb
” is displayed. Press the HELP Button to view programmed option.
2.
“
1
” is displayed. Pressing the HELP Button again to step through
0, 1, 2, 3, 4,
&
5
.
3.
To store an option selected, press the CANCEL and HELP Buttons at the same time. The unit will beep
twice while flashing the display to acknowledge that the option has been selected. Press the CANCEL
Button to move to the next Program Option.
Default Values –
Sets all Preference Programming Options to Default Values
Warning! This will Sets all Preference Programming Options to Default Values
1.
“
dF
” is displayed. Press the CANCEL and HELP Buttons at the same time and the unit will beeps three
times to indicate that ALL Preference Programming Options have been defaulted.
2.
Press the CANCEL Button to move to the next Program Option.
