background image

Chapter 3: Software Installation & Operation

Macros: This section of the window is used to save and play back macros. Macros store a set 
sequence of routes. 

To record a macro: 

Click on the Record button (last button shown above). A blinking “recording” message below 

1.

this button will be displayed to indicate that all routes are being recorded. 

Select the desired cross points. (See CATSWITCH Routing for details on making these routes.) 

2.

There is no limit on the number of routes you may record. 

If you click a macro button while in the record mode, the macro will be executed, and these 

3.

routes will be added to the recording. This makes it possible to combine the routes of two or 
more macros into one bigger macro. 

When finished, click the “Save Macro” button. You will be instructed to then click on one of the 

4.

macro buttons. Doing this will save the recorded routes to that button.

To cancel saving the macro, click the “Cancel Save” button. 

To play back a macro, simply click on one of the 50 macro buttons. Use the scroll bar to bring 

5.

any of these into view. 

The macros are automatically saved in the current configuration file. They are also saved when 

6.

you select the File/Save Configuration... menu.

To save macros in a separate file for a special purpose, select the File/Save  

 

 

 

Macros...menu.

Summary of Contents for CATSWITCH




























Reviews: