background image

 

 

www.smartdigital.com.au

 

Edition 1.2 

9

 

S

PEAKER SETUP

 

Placement of speakers 

1.

 

The HandiTheatre System is supplied standard with two (2x) 8” Behringer powered speakers.  

2.

 

To ensure optimum quality, volume and stereo separation speakers are best placed one on each 
side of the screen frame.  

Connecting speakers to SmartBox

®

 

1.

 

The HandiTheatre System is supplied standard with two (2x) 10metre Smart Digital speaker 
cables. 

2.

 

Connect the Male XLR end of one speaker cable to the 

“Line level balanced input”

 on the rear of 

the speaker (see diagram). Left and right respectively. 

3.

 

Connect the Female XLR end of the speaker cable to the Speaker Output connectors on the 
mixer section of the SmartBox (see image). Left and right respectively. 

4.

 

Turn the speakers on 

after

 the SmartBox has been turned on. 

5.

 

Connect power cable to mains power 

 

Powering ON speakers 

Once placed, connected to SmartBox

®

 and 

plugged into power; turn on each speaker using the switch located on the rear panel of the 
speaker box (you will need to repeat this for each speaker)  

NOTE: Connecting or disconnecting of SmartBox

®

 to speakers should only be 

performed whilst speakers are disconnected from mains or injury and/or damage 

may result. 

Summary of Contents for HandiTheatre













Reviews: