User guide
P.5
Note:
If the Starter Kill is installed, the vehicle will benefit from a protection against starter
motor damage that could occur after remote-starting the engine should the user, by force of
habit, turn the ignition key to the
CRANK
position.
The Starter Kill (if installed) can be configured by the installer either to
Passive Mode
(so as to arm
automatically) or
Active Mode
(so as to require the user’s intervention for arming). By default, your
Remote Car Starter is configured to
Passive Mode
.
Passive mode:
To
arm
the Starter Kill, press the
button on the transmitter,
OR
1.
In
Passive Mode
, the Starter Kill will automatically arm 1 minute (by default) or 3
minutes (if configured this way) after the ignition is turned
OFF
or once the last door is
closed (if the doors are monitored).
2.
The LED on the antenna will flash quickly during the countdown preceding the activation
of the Starter Kill.
3.
Once the activation countdown expires, the LED will send a series of quick double
flashes to indicate that the Starter Kill is now armed.
To
disarm
the Starter Kill, press the
button on the transmitter.
x
The Starter Kill will automatically rearm itself after 1 minute (by default) or 3 minutes (if
configured this way) if no door is left opened (if the doors are monitored) and the ignition
is not turned
ON
.
Active Mode:
To
arm
the Starter Kill, press the
button on the transmitter.
1.
The parking lights will flash once.
2.
The LED on the antenna will flash slowly.
3.
If remote door locks are installed, this will also lock the doors and arm the OEM-style
alarm.
To
disarm
the Starter Kill, press the
button on the transmitter.
1.
The parking lights will flash twice.
2.
The LED on the antenna will remain
OFF
.
3.
If remote door locks are installed, this will also unlock the doors.
Remote-Starting Your Vehicle
Setting Your Vehicle into Ready Mode
If your vehicle has a
manual transmission
you must read the following indications. The unit must
first be set to Ready Mode in order to start the vehicle by remote. If the unit is not set to Ready
Mode, it cannot remote start the vehicle.
Please note that Ready Mode can be enabled by the remote or the handbrake, depending on the
option that was selected by your installer. Therefore, you must follow the appropriate procedure
between the two described below in order to set your vehicle into Ready Mode.
Once the system is set to Ready Mode, the vehicle can be remote started and stopped at any time.
The system will exit Ready Mode if a door, the hood or the trunk is opened, if the brake pedal is
pressed, if the parking brake is disengaged or if the ignition key is turned to the
IGNITION ON
(RUN)
position.
P.12
User Guide
1.
Press the
or
button.
2.
Within 3 seconds, press the
and
buttons
simultaneously for 3 sec.
3.
The P-lights will flash once
To take the system out of home valet mode:
x
Turn the ignition key to the
IGNITION ON (RUN)
position.
The system will warn you if someone attempts to start your vehicle while it stands in home valet
mode. The parking lights will:
Turn
ON
then
OFF
; then
Flash
twice
, pause; then
Flash
twice
again.
AUX 1
Note:
This 500 mA negative Aux 1 output can be used for many different applications
Priority door:
This great feature allows the user to unlock solely the driver’s door with a single press of
the
button on the transmitter, and to unlock the other doors, if desired, by pressing
the
button for a second time.
The output will provide a 1-second negative output when the
button is pressed a
second time on the transmitter.
Horn Confirmation:
AUX 1
can be programmed to trigger the horn every time the
button is pressed, or
when the
button is pressed twice within 3 seconds. When horn confirmation is
activated, panic mode is enabled. If horn confirmation is disabled, panic mode will not
be available.
Horn Chirp Timing
The pulse duration can be configured by your installer (from 5 ms to 200 ms).
Multi-car Operation
This option allows the owner of two vehicles, both equipped with the same Remote Car Starter
model, to control both systems with a single remote control. To control the second vehicle,
simultaneously press the
TRUNK
button and the button of the function you wish to use.
Note:
Your remote control must be configured for second car operation by the installer.
Press
TRUNK
+
LOCK
buttons simultaneously: ..
LOCK
Press
TRUNK
+
UNLOCK
simultaneously: ..........
UNLOCK
Press
TRUNK
+
START
simultaneously: ..............
START
Press
TRUNK
+
STOP
simultaneously: ................
STOP
Press
TRUNK
+
START
simultaneously for 3 sec:
Cold Weather Mode
OEM-Style Alarm
The OEM-style alarm (if configured by your installer) monitors the doors, hood and ignition switch
of your vehicle. It will sound the horn if a door or the hood is opened, or if the key is turned in the
ignition.
x
To
arm
the OEM-style alarm, press the
button on the transmitter.
-The OEM-style alarm will ONLY arm if the
button on the transmitter is pressed.
-The LED on the antenna will flash slowly to indicate that the OEM-style alarm is now armed.
