User guide
P.7
Remote Starter Features
Remote Door Locks
If your system was installed with the Remote Door Locks option, you will have the convenience of
remote keyless entry.
To lock your doors and arm the starter kill (if installed):
1.
Press and hold the
button for approx. 1 sec.
2.
The parking lights will flash once to confirm that the doors have been locked
To unlock your doors and disarm the starter kill (if installed):
1.
Press and hold the
button for approx. 1 sec.
2.
The parking lights will flash twice to confirm that the doors have been unlocked.
Remote Trunk Release
If your system was installed with the Remote Trunk Release option, you can open your trunk by
pressing the
button for 3 seconds on the remote transmitter.
Idle Mode
Convenience feature:
Idle Mode allows you to keep the engine running and the doors locked
while you stop, for example, at a convenience store or for a short delivery.
This feature allows you to let the remote starter take over control of the vehicle (i.e. no Key in the
Ignition Switch) while the engine is running.
Activating Idle mode (Automatic transmission):
1.
With the engine running, make sure to release the brake pedal and press the
,
or
button on the transmitter until the parking lights come
ON
.
Note:
SmartStart™ can be setup to use the
icon to activate Idle mode.
2.
Remove the ignition key from the ignition switch.
The engine will continue running.
3.
Exit the vehicle. All doors, the hood and trunk should be closed
4.
Press the
button to lock the doors, to arm the starter kill and to arm the alarm. The
engine will be kept running at idle speed.
a.
When re-entering the vehicle, the user must reinsert the key into the ignition and
turn it to the
ON
position (not Crank) without pressing on the brake.
b.
Once the key is in the ON position
, press on the brake pedal to put the
transmission in gear.
c.
Drive off.
If your vehicle has a manual transmission, Idle Mode can be activated through the same routine as
that used for
Ready Mode
(page-5)
; at the last step, the
button is pressed instead of the other
buttons. This will lock the doors, arm the system and leave the engine running.
NEW FEATURE –
Push-To-Start Idle Mode
This feature is a variation of “Idle mode”, but made specifically for Push-To-Start vehicles, with
automatic or manual transmissions. (Consult your installer for availability of this feature.) Follow the
same steps as the normal Idle Mode procedure, except for when re-entering the vehicle while the
engine is running;
1.
Press unlock
P.10
User Guide
Example:
If your Module is programmed for a runtime of 3 minutes and your vehicle has been
running for 2 minutes already, pressing the
button will reset the counter to zero and the Engine
will run for another cycle (in this case, 3 minutes).
Disable/Enable LED flashing
To disable the LED:
Press
and
simultaneously until the parking lights flash three
times.
To Enable the LED:
Press
and
simultaneously until the parking lights flash once.
Constant output
x
Pressing and holding the
button for more than 3 seconds will lock all doors and will
send a constant pulse as long as the
button is held down (maximum of 15 seconds).
This constant pulse can be configured to activate certain functionalities such as rolling up
the
windows
–
Please refer to your installer to see if your vehicle is compatible with
this
option.
x
Pressing and holding the
button for more than 3 seconds will unlock all doors and will
send a constant pulse as long as the
button is held down (maximum of 15 seconds).
This constant pulse can be configured to activate certain functionalities such as rolling
down
the
windows
–
Please refer to your installer to see if your vehicle is compatible
with this option.
Advanced Features: Installation-programmable
Options
The Remote Car Starter was designed with flexibility and OEM integration in mind. With its
programmable options, this unit can single-handedly control nearly any electrical system in your
vehicle.
Caution
:
The programming of your system should be left to a professional. Changing any
one of the settings may affect the operation of your Remote Car Starter. Please note that the
following programmable options may require additional parts and labor.
Ignition-controlled Door Locks
This is an added security feature. If your Remote Car Starter was installed with the Ignition-
Controlled Door Locks option, the doors will automatically be locked as soon as the ignition key is
turned to the
IGNITION ON (RUN)
position while the brakes are pressed. The remote car starter
will also lock any door that was unlocked and opened (then closed) the next time the brake pedal is
pressed. When the key is turned to the
OFF
position, the doors will automatically be unlocked.
Secure Lock
(Disabled by default.) Before your vehicle can be remote-started, the factory security system must
first be disarmed. The Secure Lock feature may be required on certain vehicle models with factory
security systems that automatically unlock the doors when the security system is disarmed.
To keep your vehicle protected when the factory security system is disarmed for a remote start,
Secure Lock will relock your doors as soon as the vehicle is started. Once the engine is shut down
by remote or after its runtime has expired, Secure Lock will also rearm your factory security system
and relock the doors.