Ignition
“On”
When Ready to Drive: Regular Key
1. Turn ignition key to the “ON” or “RUN” position
2. Depress the brake pedal to shift out of “Park”
(second
click)
Note: Do not turn past the “ON” position to “START”!
(this automatically turns off remote start system)
Ignition
“On”
When Ready to Drive: “I-Key” (V1)
1. With I-Key inside vehicle, turn ignition switch to the “ON” or
“RUN” position
2. Depress the brake pedal to shift out of “Park”
(second click)
Note: Do not turn past the “ON” position to “START”!
(this automatically turns off remote start system)
Door open
When Ready to Drive: “I-Key” (V2-Securelock)
1. Open the driver’s door...
2. Engine turns off automatically (Remote Start shuts down)...
3. With I-Key inside vehicle, restart vehicle manually with
ignition switch.
Vehicle will not attempt to remote start with door open.
Note:
START
STOP
When Ready to Drive: “I-Key” (V3)
1. With I-Key inside vehicle, push “START” button on
dashboard once, to turn to “ACC” position...
2. Push “START” button second time to turn to the “ON”
position...
3. Depress the brake pedal to shift out of “Park”
(this automatically turns off remote start system)
BRAKE
When Ready to Drive: All Vehicles
1. Depress brake pedal...
2. Engine turns off automatically (Remote Start shuts down)...
3. Restart vehicle manually with ignition switch.
V
REMOTE STOP VEHICLE
1. Press & hold the “START” button for 4 seconds.
2. Park lights will flash and vehicle shuts down.
Note: Pressing on brake pedal will also stop the engine
QUICK STOP MODE
(not available on some vehicles)
1. While vehicle is running with key, press & release the START button.
2. Park lights will turn “ON”. Turn ignition “OFF” and remove key.
3. Vehicle continues to run for 15 minutes, allowing you to run quick errands.
4. When you return, follow “WHEN READY TO DRIVE” procedure.
REMOTE START VEHICLE
1. Press & release the “START” button
2. Park lights will flash to confirm that remote start
command has been received
3. Vehicle’s engine will start.
4. Park lights will remain “ON” while engine is running
5. Follow “When ready to Drive” procedure below.
6. Vehicle will run for 15 minutes and shut down.
*
start
REMOTE RUNTIME EXTENSION
1. While vehicle is running with remote start, press & release the “START”
button to reset the timer and extend the runtime.
2. Park lights flash 1 time to confirm the extension of runtime
(15 min timer restarts).
Condition #1
Advice
Parking lights flash 3 times and vehicle does not proceed to start...
The system is in “Service Mode” (see Service Mode procedure)
Vehicle’s starter engages but engine does not start.
Parking lights flash 4-7 times and vehicle does not proceed to start...
Contact customer service for assistance at (847)338-7898.
Condition#2
Condition#3
Advice
REMOTE START [BC-118]
SERVICE MODE
TO ACTIVATE SERVICE MODE
TO EXIT SERVICE MODE
1. Locate the “service” button inside the vehicle
2. Turn ignition key “ON”, then press and hold the “service”
button for 15 seconds.
3. Park lights flash 5 times.
4. Release the button and turn ignition key off.
5. Remote start functions will be disabled and LED light will
stay “on”.
1. Turn ignition key “ON”, then press and hold the “service”
button for 15 seconds.
2. Park lights flash 2 times.
3. Release the button and turn ignition key off.
4. Remote start functions will be enabled and LED light will
stay “off”.
(BC-118: on the windshield antenna)
(BC-116: inside fusebox or under dash)
(all systems)
SERVICE MODE
-While Service Mode is activated, if you press the “start” button, the parking lights
flash three (3) times and vehicle does not remote start.
15 sec.
Ignition
“On”
15 sec.
OR
REMOTE START [BC-116]
FCC Notice
This device complies with Part 15 of the FCC rules. Operation of this device is subject to the following conditions: (1)
This device may not cause harmful interference, and (2) This device must accept any interference received, including
interference that may cause undesired operation. CAUTION: Changes or modifications not expressly approved by
the part responsible for compliance voids the users authority to operate this device.
-Service Mode must be used to disable Remote Start system for
vehicle servicing (i.e. oil changes, tune-ups, etc) or when
parking in an enclosed garage. Service Mode will disable the
Remote Start system from activating until Service Mode is
deactivated.
WHEN READY TO DRIVE (all systems)
While remote started, follow the “Key-Take-Over” procedures outlined below.
Procedure(s) with check mark
apply to your vehicle.
V
Auto-Dimming
Rearview Mirrors
with Compass, Temperature
and HomeLink Options
Reversing Aid
Collision Avoidance System
with In-Bumper Sensors
Bluetooth Hands-free
Cellular Phone Car Kits
with Caller ID
Also available from
SMART
START
-Warning: Never Start any Vehicle in Enclosed Building or Garage
Carbon Monoxide may cause serious injury, even death!
-The Remote Start system must be placed into Service Mode before any
service/maintanance work is started or when parking in an enclosed area/garage. It is
the sole responsibility of the vehicle’s owner to ensure that this is done.
-Warning: Children should never play with vehicle’s keys or remote transmiters!
The manufacturer and the installation center accept no liability or responsibility for
accidental starting of the vehicle.
!
LED
LED
