background image

Dual mount motion and occupancy sensor 

User manual

 

 

Rev. 1 del 10.11.2022 

Pag.  2/9 

 

 

 

General Safety Rules 

Before using this device, certain precautions must be taken to reduce any risk of fire and / or personal 
injury: 

1. 

Read  all  instructions  carefully  and  follow  all  precautions  contained  in  this  manual.  All  direct 
connections to the mains conductors must be made by trained and authorized technical personnel. 

2. 

Pay  attention  to  all  possible  danger  indications  reported  on  the  device  and  /  or  contained  in  this 

manual, highlighted with the symbol 

3. 

Disconnect the device from the power supply or battery charger before cleaning it. For cleaning, do 
not use detergents but only a damp cloth. 

4. 

Do not use the device in gas saturated environments. 

5. 

Do not place the device near heat sources. 

6. 

Use only the original EcoDHOME accessories supplied by SmartDHOME. 

7. 

Do not place the connection and / or power cables under heavy objects, avoid paths near sharp or 
abrasive objects, prevent them from being walked on. 

8. 

Keep out of the reach of children. 

9. 

Do not carry out any maintenance on the device but always contact the assistance network. 

10. 

Contact the service network if one or more of the following conditions occur on the product and / or 
an accessory (supplied or optional): 

a. 

If the product has come into contact with water or liquid substances. 

b. 

If the product has suffered obvious damage to the container. 

c. 

If the product does not provide performance conforming to its characteristics. 

d. 

If the product has undergone a noticeable degradation in performance. 

e. 

If the power cord has been damaged. 

Note: 

Under  one  or  more  of  these  conditions,  do  not  attempt  to  make  any  repairs  or  adjustments  not 

described in this manual. Improper interventions could damage the product, force additional work to regain 
the desired operation and exclude the product from the warranty.

 

ATTENTION! 

Any  type  of  intervention  by  our  technicians,  which  will  be  caused  by  improperly  performed 

installation or by a failure caused by improper use, will be charged to the customer. 

Provision for Waste  Electrical  and Electronic  Equipment. (Applicable in the European Union and in 
other European countries with the separate collection system). 

This symbol found on the product or its packaging indicates that this product must not be treated as 
common  household  waste.  All  products  marked  with  this  symbol  must  be  disposed  of  through 
appropriate  collection  centers.  Improper  disposal  could  have  negative  consequences  for  the 

environment and for the safety of human health. Recycling of materials helps to conserve natural resources. 
For more information, contact the Civic Office in your area, the waste collection service or the center where 
you purchased the product. 

 

Summary of Contents for 01335-1900-00










Reviews: