background image

Page2

Steam press Instruction Manual

SAFETY REMINDERS

WARNING - 

Read all of the instructions and then save them for future reference.

TO PROTECT

 against the risk of electric shock, 

DO NOT

 

immerse the appliance in water.

 

ALWAYS

 turn the switch to the OFF position before plugging in or 

unplugging the unit.

 DO NOT

 let the cord hang over the edge of counters.

 DO NOT

 allow the cord to touch hot surfaces.

 ALWAYS

 allow the appliance to cool completely for at least thirty 

minutes before storing.

 ALWAYS

 put the appliance in a secure place on a table or counter 

when using.

 DO NOT

 move the appliance without unplugging it first.

 The appliance has very hot surfaces - 

DO NOT

 allow unsupervised 

children to use the appliance.

ALWAYS

 disconnect the appliance from the outlet 

BEFORE

 

filling with or removing water. Be careful to avoid spilling water 
on the appliance when filling.

USE DISTILLED WATER

 in the appliance. 

DO NOT

 use 

perfume or products containing alcohol in the appliance.

 ALWAYS

 disconnect the appliance when not in use.

 

DO NOT

 use the appliance if the cord gets damaged. Return the 

appliance or have the cord repaired by a licensed electrician.

 DO NOT

 operate the appliance if it has been dropped or damaged. 

 

DO NOT

 disassemble the appliance. Incorrect reassembly can 

cause a risk of electric shock.  Send it to an authorized service 
center for repair.

DO NOT

 operate another high wattage appliance on the same 

circuit.

If an 

EXTENSION CORD

 is necessary, use a 13 Ampere cord (for 

110V/120V) appliances. Cords rated for less amperage may 
overheat.

This appliance 

MUST BE

 grounded. 

 DO NOT

 alter the plug or 

attempt to defeat this feature.

 Be careful. Burns can occur from touching

 HOT METAL PARTS, 

HOT WATER or STEAM.

a

Summary of Contents for ST-X500



















Reviews: