background image

Plug-in incandescent, fluorescent, inductive lighting devices
400 Watts
1 Base (Primary) Address of 256 possible
Up to 64 Scene Addresses 

(Plus only)

(Primary Address) 1 of 31 possible (3.2%-100%) or resume dim
(Scene Address) 1 of 32 possible (0%-100%) 

(Plus only)

0.125 to 9 seconds if programmed locally
0.125 seconds to 9 minutes if programmed remotely
10 (with more than 6, a PLC amplified coupler-repeater
is highly recommended)
25 watts
10 mV
MOV rated for 150 Volts
Maximum 15 amps less the load controlled by the LampLinc module
120 Volts AC +/- 10%, 60 Hertz
32 to 122 degrees Fahrenheit
4”(h) x 2.5”(w) x 1.5”(d)
5 oz

Load Types:
Maximum Load:
Addresses:

On-Level:

Fade-On/Off Rate:

Maximum number of LampLincs
per circuit:
Minimum load:
Minimum PLC receive level:
Surge Protection:
Feed through outlet:
Input Power:
Operating Temperature:
Dimensions:
Weight:

SPECIFICATIONS

Limited Warranty

Seller warrants to the original consumer purchaser of this product that, for a period of two years from the date of
purchase, this product will be free from defects in material and workmanship and will perform in substantial
conformity to the description of the product in this Owner’s Manual. This warranty shall not apply to defects
or errors caused by misuse or neglect.
If the product is found to be defective in material or workmanship, or if the product does not perform as war-
ranted above during the warranty period, Seller will either repair it, replace it or refund the purchase price,
at its option, upon receipt of the product at the address below, postage prepaid, with proof of the date of
purchase and an explanation of the defect or error. The repair, replacement, or refund that is provided for
above shall be the full extent of Seller's liability with respect to this product.
For repair or replacement during the warranty period, call Smarthome customer service to receive an RA# (return
authorization number), properly package the product (with the RA# clearly printed on the outside of the package)
and send the product, along with all other required materials, to:

Smarthome, Inc.

ATTN: Receiving Dept.
16542 Millikan Ave.
Irvine, CA 92606-5027

Limitations:

The above warranty is in lieu of and seller disclaims all other warranties, whether oral or written, express or
implied, including and warranty or merchantability or fitness for a particular purpose. Any implied warranty,
including any warranty of merchantability or fitness for a particular purpose, which may not be disclaimed or sup-
planted as provided above shall be limited to the one year period of the express warranty above. No other repre-
sentation or claim of any nature by any person shall, be binding upon seller or modify the terms of the above
warranty and disclaimer.
In no event shall seller be liable for special, incidental, consequential, or other damages resulting from the
possession or use of this product, including without limitation damage to property and, to the extent permit-
ted by law, personal injury, even if seller knew or should have known of the possibility of such damages.
Some states do not allow limitations on how long an implied warranty lasts and/or the exclusion or limitation
of damages, in which case the above limitations and/or exclusions may not apply to you. You may also have
other legal rights that may vary from state to state.

ControLinc, TesterLinc, SignaLinc, LampLinc, ToggleLinc, BoosterLinc, ApplianceLinc, KeypadLinc, FilterLinc,

ProbeLinc, SwitchLinc, TempLinc, IR Linc & SmarthomeLive are trademarked by Smarthome, Inc.

© Copyright 2004 Smarthome, 16542 Millikan Ave., Irvine, CA 92606-5027

800.SMART.HOME - 949.221.9200 - www.smarthome.com

rev 031504

LampLink Plus& PLC for web (Mar04).qxd  3/15/2004  9:59 AM  Page 12

Summary of Contents for LampLinc Plus 2000SLS













Reviews: