SMC Networks EX250-SPR1 Operation Manual Download

Page: 29 / 31

-28-

No.EX

※※

-OME0014-F

Specification

■

Specifications

General specification

Item

Specification

Operating ambient temp.

-10 to +50

Operating ambient humidity

35 to 85%RH (No dew condensation)

Storage ambient temp.

-20 to +60

Withstand voltage

500 VAC for 1 min.

Insulation resistance

500 VDC 10 M

Ω

or more

Operating environment

No corrosive gas

Pollution degree

Pollution degree 3

Enclosure IP67
Applicable standard

UL/CSA, CE

Electrical specification

Item

Specification

Power for SI/Input
Block Current
consumption

19.2 to 28.8 VDC
Depending on the number of Input Block stations and sensor specifications:
1.1 A or less
(Inside SI unit: 0.1 A or less)

Power Voltage
range, current
consumption

Power for solenoid
valve Current
consumption

22.8 to 26.4 VDC
Depending on number of solenoid valve station and specifications:
2.0 A or less

Output type

Source / PNP (negative common)

Connection load

Solenoid valve with surge voltage suppressor of 24 VDC and 1.5 W or less
(manufactured by SMC)

Insulation type

Photo coupler type

Solenoid valve
connection
specification

Residual Voltage

0.3 VDC or less

Communication specification

Item

Specification

Protocol

PROFIBUS DP (EN50170, EN50254)

BUS

Interface EIA

RS-485

Communication form

Token passing

Transmission speed

9.6/19.2/45.45/93.75/187.5/500/1500/12000 kbps

Transmission media

STP cable

Connect node

Max. 125 station

Network topology

Bus, tree, star

Cable length

Max. 23 km (Repeater needed)

Freeze mode

Available

Sync mode

Available

Input point

Max. 32 points

Output point

Max. 32 points

ID number

1408 hex (SW setting mode)
1409 hex (HW setting mode)

Applicable solenoid valves

Representative series

Applicable series

VQC series

VQC1000, VQC2000, VQC4000

SV series

SV1000, SV2000, SV3000 (Tie-rod base manifold)

S0700 series

S0700

Summary of Contents for EX250-SPR1
































Search results

Summary of Contents for EX250-SPR1

Reviews:

Related manuals for EX250-SPR1

Brands by name

Popular brands

SMC Networks EX250-SPR1, Operation Manual

Search results

Summary of Contents for EX250-SPR1

Reviews:

Related manuals for EX250-SPR1

Brands by name

Popular brands