background image

 

iv

CE Mark Declaration of Conformance for EMI and Safety (EEC)

This information technology equipment complies with the requirements of the 
Council Directive 89/336/EEC on the Approximation of the laws of the Member 
States relating to Electromagnetic Compatibility and 73/23/EEC for electrical 
equipment used within certain voltage limits and the Amendment Directive 93/68/
EEC. For the evaluation of the compliance with these Directives, the following 
standards were applied:

Warning! 

Do not plug a phone jack connector in the RJ-45 port. This may damage 

the device. Les raccordeurs ne sont pas utilisé pour le système téléphonique!

Australia AS/NZS 3548 (1995) - Class A

RFI 
Emission:

• Limit class A according to EN 55022:1998

• Limit class A for harmonic current emission according to 

EN 61000-3-2/1995

• Limitation of voltage fluctuation and flicker in low-voltage 

supply system according to EN 61000-3-3/1995

Immunity:

• Product family standard according to EN 55024:1998

• Electrostatic Discharge according to EN 61000-4-2:1995 

(Contact Discharge: ±4 kV, Air Discharge: ±8 kV)

• Radio-frequency electromagnetic field according to 

EN 61000-4-3:1996 
(80 - 1000 MHz with 1 kHz AM 80% Modulation: 3 V/m)

• Electrical fast transient/burst according to EN 61000-4-4:1995 

(AC/DC power supply: ±1 kV, Data/Signal lines: ±0.5 kV)

• Surge immunity test according to EN 61000-4-5:1995 

(AC/DC Line to Line: ±1 kV, AC/DC Line to Earth: ±2 kV)

• Immunity to conducted disturbances, Induced by 

radio-frequency fields: EN 61000-4-6:1996 
(0.15 - 80 MHz with 1 kHz AM 80% Modulation: 3 V/m)

• Power frequency magnetic field immunity test according to 

EN 61000-4-8:1993 (1 A/m at frequency 50 Hz)

• Voltage dips, short interruptions and voltage variations 

immunity test according to EN 61000-4-11:1994 
(>95% Reduction @10 ms, 30% Reduction @500 ms, >95% 
Reduction @5000 ms)

LVD:

• EN 60950-1

N11846

Summary of Contents for EZ Switch SMCFS26





























Reviews: