background image

 

Communication Format

 

3-4 

 

INR-244-831 

3.5 

Explanation of Code 

 

  STX 

The code necessary for the receiver to detect the beginning of a 
message. It is put at the beginning of sent characters. 

  Address 

The address to which (this product) the master communicates. The 
address in a response message from this product shows where the 
message is sent.   

  Content 

One of two symbols, R or W. 

R: Read data from the product 

W: Write or store data to the product 

  Identification 

The classification symbol (identification code) of read or written data with 
3 digit alphabetical ASCII codes. Refer to page 3-9 

“3.9 Identification 

Code List

  Numeric data 

Read or written data with 5 digits regardless of its type.   
Minus data: 

“- (symbol for minus)“ is displayed at the 1

st

 digit   

Position of decimal point: Not included in 5 digit data. 
Ex) The 5 digit numeric data means 
 

Ex. 

Meaning of numerical data 

Target temp., measured 
temp., and offset value 

00010: 1.0°C 

Control mode 

00000: Temperature control enable(Run) 
00002: Temperature control diseble(Rdy) 

  ETX 

The code necessary for the receiver to know the message is complete. It 
is put at the end of sent characters (except for BCC). 

  BCC 

Exclusive OR (EX-OR) of all characters from STX to ETX are taken in. 
If 

BCC check is set to “no function” in the comunication setting mode of 

the product, this code is not included in 

the “response message”. 

  ACK 

The affirmation code included in the 

“response message” of the 

product; it is sent when the received 

“request message” contains no 

errors. 

  NAK 

Summary of Contents for Thermo-con INR-244-831























Reviews: