19
disconnection of the mains under conditions relating to over-
current category III, in accordance with installation
instructions.
Warning!
Before re-connecting the hood circuit to the mains
supply and checking the efficient function, always check that
the mains cable is correctly assembled.
Mounting
Expansion wall plugs are provided to secure the hood to most
types of walls/ceilings. However, a qualified technician must
verify suitability of the materials in accordance with the type of
wall/ceiling. The wall/ceiling must be strong enough to take
the weight of the hood.
Do not tile, grout or silicone this
appliance to the wall. Surface mounting only.
Preliminary information for installation of the hood:
Disconnect the hood during electrical connection, by turning
the home mains switch off.
Remove the fat/s filter/s and the carbon filter frame.
Do not tile, grout or silicone this appliance to the wall. Surface
mounting only. Do not fix chimney flue to furniture or fly over
shelves unless the chimney flue can be easily removed, in
case maintenance is ever required.
Assembling the chimney flue support/bracket (3 parts):
The three parts should be fixed with 4 screws, the support
extension is adjustable and should correspond to the internal
width of the telescopic chimney flue.
A
ssembling the deflector (only when a deflector
composed of 3 parts is supplied – the deflector should be
only for the filter version):
The three parts should be fixed with 2 screws, the deflector
extension is adjustable and should correspond to the width of
the chimney flue support, to which it is then fixed.
Only for the models illustrated in Fig. 1D/8D - 1E/8E -
1Q/8Q
Remove AND CONSERVE the screws that temporarily fix
the flue units (for reasons of transport), the hood or the
flue unit (on the basis of the model possessed) with the
suction unit.
The two parts should be disassembled to
facilitate installation. Check how the parts are fixed together
to repeat assemblage at the opportune moment.
Before fixing the hood to the suction unit check that the metal
band (steam shield) that holds the lamp and the filter/s /
greases is well attached to the front. If necessary adjust the
position of the band forwards until the end stop.
Attention!
The chimney is predisposed for installation of the filter
Version.
In certain models where it is required to use the cooker hood
in the suction version then it is possible to overturn the upper
section of the chimney
and insert it inside the lower section of the chimney so that the
air-exit perforations are not visible. The chimneys in which
this operation is possible are recognizable by their bracket
fixing points
G
which are repeated also in the lower side of the
upper section of the chimney (see installation sequence 20a-
20b).
Attention!
for all pre-assembled models:
the mounting operations
“1, 2, 3”
should not be taken into
consideration, for installation begin at operation
“4”
.
1.
Rest the suction unit on a flat surface and thread the
lower part of the hood onto it (consult the figure
corresponding to the model in possession - Fig. 1C/8C -
1D/8D - 1I/8I - 1E/8E - 1F/8F - 1G/8G - 1H/8H - 1R/8R -
1N-1O-1P)
.
2.
Make all the electrical connections between the two parts
(Fig. 9)
.
3.
Permanently fix the cooker hood to the suction group with
the screws (consult the figure corresponding to the model
in possession - Fig. 1C/8C - 1D/8D - 1I/8I - 1E/8E - 1F/8F
- 1G/8G - 1H/8H - 1R/8R - 1N-1O-1P)
.
4.
Using a pencil, draw a line on the wall, extending up to
the ceiling, to mark the centre. This will facilitate
installation
(Fig. 10)
.
5.
Rest the drilling template against the wall: the vertical
centre line printed on the drilling template must
correspond to the centre line drawn on the wall, and the
bottom edge of the drilling template must correspond to
the bottom edge of the hood: bear in mind that, when
installation is complete, the underside of the hood must
be at least 50 cm above the cooker top in the case of
electric cookers, and at least 65 cm above the cooker top
in the case of gas or mixed cookers.
6.
Place the lower support bracket on the perforation
diagram making it coincide with the traced triangle, mark
the two external holes and perforate. Remove the
perforation diagram, insert two wall-dowels and fix the
support bracket of the hood with two 5x45 mm screws
(Fig. 10)
.
Attention: only the models illustrated in Fig. 1Q/10Q:
Fix the central bracket with two screws and wall-dowels
above the lower bracket (see perforation diagram for
positioning the holes).
7.
If supplied dismantled, fix the hooks to the side of the
aspiration group with two screws (fig. 10a). Hang the
hood onto the lower bracket.
8.
Adjust the distance of the hood from the wall.
9.
Adjust the horizontal position of the hood.
10.
Using a pencil mark the cooker hood permanent drill hole
