21
Functioning - 5-key electronic model
1 2 3
O
O
I
F C
1 2 3 4
5 6 7
8
9
1.
Motor OFF button
2.
ON button and motor speed selection button 1 - 2 - 3 - 1 -
2 - . . . .
3.
Speed 1 LED
4.
Speed 2 LED and metal grease filter saturation LED (in
this latter case, the LED will flash - See instructions on
grease filter cleaning).
Once the grease filters have been cleaned, press button
1 for about 3 seconds until you hear the acoustic signal
(beep): the LED 4 will now stop flashing.
5.
Speed 3 LED and active carbon filter saturation LED (in
this latter case, the LED will flash - See instructions on
active carbon filter replacement).
Once you have replaced the charcoal filter, press button
1 for about 3 seconds until you hear the acoustic signal
(beep). LED 5 will now stop flashing.
Warning!
The active carbon filter saturation LED is not activated.
In order to activate the active carbon filter saturation
indicator, press buttons 2 and 7 simultaneously for 3
seconds. Initially, only LED 4 will flash, then after the 3
seconds have passed, LED 5 will also start flashing,
indicating that the active carbon filter saturation control
system is active.
To switch off the system, re-press the same two buttons:
after 3 seconds LED 5 will stop flashing and the device
will be switched off.
6.
Intensive speed LED
7.
Intensive speed ON switch
This speed should be used when the concentration of
cooking fumes or odours is particularly strong (for
example when frying, cooking fish etc.).
The fast speed will run for about 5 minutes and then
return to the speed previously set automatically (1, 2 or
3), or switch off if no speed was selected.
To turn off the fast speed, before the end of the 5
minutes, press button 1 or button 2.
8.
OFF lamp button
9.
ON lamp button
If the hood fails to operate correctly, briefly disconnect it from
the mains power supply for almost 5 sec. by pulling out the
plug. Then plug it in again and try once more before
contacting the Technical Assistance Service.
Functioning - Model with display
A
B
C
D
F
E
G
A.
OFF key (Display off) /Stand-by (led lit on the display) –
press for a long time to select the function desired.
B.
Lighting, on/off.
C.
Timer for selected speed (visualizes the speed selected
and flashing LED on the lower side of the display).
This knob permits the operation of the cooker hood for a
established period:
20 minutes if the speed selected is 1
15 minutes if the speed selected is 2
10 minutes if the speed selected is 3
5 minutes if the intensive speed P is selected.
D.
Display showing:
• Fan speed (1-3-P).
• Change grease filters (grease filter saturation indicator
- F)
After washing the anti-grease filter, depress knob A
for about 3 seconds. The letter F will disappear from
the display.
• Change activated carbon filters (carbon filter
saturation indicator - C).
After replacing the charcoal filter, depress knob A for
about 3 seconds. The letter C will disappear from the
display.
• When the led in the lower right side is on, it indicates
that the cooker hood is ready for operation (“standby”
position), the flashing LED indicates that the timer has
been activated for selected speed.
Attention! The active carbon filter saturation indicator is
normally deactivated, to activate it:
Set the hood on OFF (display off), press keys C and G
contemporaneously for 3 secs.
Initially, only letter F will fbe displayed, then after the 3
seconds have passed, letter C will be displayed as well,
indicating that the carbon filter saturation control system is
active.
To switch off the system, re-press the same two buttons:
letter C appear on display and after 3 seconds letter it
disappear and the device will be switched off.
E.
Knob to decrease the speed.
F.
Knob to increase the speed.
G.
Timed intensive speed button: the hood operates at this
speed for 5 minutes and than returns to the previus settings.
The display will show P and a blinking dot. This function can
be cancelled by pressing button A.
If the hood fails to operate correctly, briefly disconnect it from
the mains power supply for almost 5 sec. by pulling out the
plug. Then plug it in again and try once more before
contacting the Technical Assistance Service.
Warning! Always press the fan off button
A
before
disconnecting the hood from the mains supply.
