background image

Cleaning and maintenance

64

4 Cleaning and maintenance

4.1 Instructions

4.2 Cleaning the appliance

Recommendations for cleaning the hob

To keep the surfaces in good condition, 
they should be cleaned regularly after use. 
Let them cool first.

Cleaning the hob

1. Pour some non-abrasive detergent on a 

damp cloth and wipe the surface.

2. Rinse thoroughly.

3. Dry with a soft cloth or a microfibre cloth.

Cleaning the hob grids, flame-spreader 
crowns and burner caps

1. Remove the components from the hob.
2. Clean with lukewarm water and non-

abrasive detergent. Make sure to 
remove any encrustations.

3. Dry thoroughly with a soft cloth or a 

microfibre cloth.

4. Replace the components on the hob.

Improper use

Risk of damage to surfaces

•  Do not use steam jets to clean the 

appliance.

•  Do not use cleaning products containing 

chlorine, ammonia or bleach on parts 
made of steel or that have metallic 
surface finishes (e.g. anodizing, nickel- 
or chromium-plating).

•  Do not use abrasive or corrosive 

detergents (e.g. scouring powders, stain 
removers and metallic sponges) on 
glass parts.

•  Do not use rough or abrasive materials 

or sharp metal scrapers.

•  Do not wash the removable 

components such as the hob grids, 
flame-spreader crowns and burner caps 
in a dishwasher.

We recommend the use of 
cleaning products distributed by 
the manufacturer.

The continuous contact between 
the grids and the flame can cause 
modifications to the enamel over 
time in those parts exposed to 
heat. This is a completely natural 
phenomenon which has no effect 
on the operation of this 
component.

Summary of Contents for Mista Aesthetic B601GMXI9









































Reviews: