background image

 

Instructions for proper use 

 

4

 

 

 

1.

 

INSTRUCTIONS FOR PROPER USE 

 

ELECTRICAL CONNECTION: PLEASE REFER TO INSTALLATION INSTRUCTIONS FOR THE GAS 
& ELECTRICAL SAFETY REGULATIONS AND THE VENTILATION REQUIREMENTS. 
IN YOUR OWN INTEREST, AND THAT OF SAFETY, IT IS THE LAW THAT ALL GAS AND 
ELECTRICAL APPLIANCES BE INSTALLED AND SERVICED BY COMPETENT PERSONS, WHO 
WILL COMPLY WITH THE RELEVANT STANDARDS AND REGULATIONS. 
SMEG REGISTERED INSTALLERS UNDERTAKE TO WORK TO SATISFCTIORY STANDARDS. 
DISCONNECTION OF GAS AND ELECTRIC APPLIANCES SHOULD ALWAYS BE CARRIED OUT 
BY COMPETENT PERSONS 

 

THIS MANUAL IS  AN INTEGRAL PART OF THE APPLIANCE AND THEREFORE MUST BE KEPT 
IN ITS ENTIRETY AND IN AN ACCESSIBLE PLACE FOR THE WHOLE WORKING LIFE OF THE  
HOB. WE ADVISE READING THIS MANUAL AND ALL THE INSTRUCTIONS THEREIN BEFORE 
USING THE  HOB. INSTALLATION MUST BE CARRIED OUT BY QUALIFIED PERSONNEL  IN 
ACCORDANCE WITH THE REGULATIONS IN FORCE. THIS APPLIANCE IS INTENDED FOR 
DOMESTIC USES AND CONFORMS TO CURRENT 

REGULATIONS IN FORCE

. THE APPLIANCE 

HAS BEEN BUILT TO CARRY OUT THE FOLLOWING FUNCTIONS: 

COOKING AND HEATING-UP 

OF FOOD

. ALL OTHER USES ARE CONSIDERED IMPROPER.  

THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR IMPROPER USE.

 

 

NEVER USE THIS APPLIANCE FOR HEATING ROOMS. 

 

 

DO NOT LEAVE THE PACKING IN THE HOME ENVIRONMENT.  SEPARATE THE VARIOUS 
WASTE MATERIALS  AND TAKE THEM TO THE NEAREST SPECIAL GARBAGE COLLECTION 
CENTRE. 

 

THIS APPLIANCE IS MARKED ACCORDING TO THE EUROPEAN DIRECTIVE 2002/96/EC ON 
WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT (WEEE). 
THIS GUIDELINE IS THE FRAME OF A EUROPEAN-WIDE VALIDITY OF RETURN AND 
RECYCLING ON WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT. 

 

THE IDENTIFICATION PLATE, WITH TECHNICAL DATA, SERIAL NUMBER AND MARKING IS 
CLEARLY VISIBLE UNDER THE CASING. 

THE PLATE ON THE CASING MUST NOT BE REMOVED.

 

 

TAKE CARE NOT TO SPILL SUGAR OR SWEET MIXTURES ON TO THE  HOB 
WHEN HOT. NEVER PLACE MATERIALS OR SUBSTANCES WHICH MAY MELT 
(PLASTIC OR ALUMINIUM FOIL) ON THE HOB. IN THE EVENT, PROMPTLY 
SWITCH OFF AND REMOVE THE MOLTEN MATERIAL WITH THE SCRAPER 
PROVIDED WHILE THE COOKING ZONE IS STILL WARM TO PREVENT IT 
FROM BEING DAMAGED. 

FAILURE TO INSTANTLY CLEAN THE CERAMIC 

HOB COULD LEAD TO ENCRUSTATIONS WHICH ARE IMPOSSIBLE TO 
REMOVE ONCE THE HOB HAS COOLED DOWN. 

 

 

The manufacturer declines all responsibility 

for damage to persons or things caused by non-

observance of the above prescriptions or by interference with any part of the appliance or by the use 

of non-original spares. 

Summary of Contents for SE2641NO
















Reviews: