background image

 

 

 

 

 

 

 

 

 

 

 

 

GB 

 

 

11

 

 

 

 

 

Options buttons 

The options that may be available on the washing machine 
are shown below. 

 

 

 

 

Quick wash Button 

 

This button reduces the overall duration of the washing cycle. This 
option is used to wash small loads or less dirty washing in less time.

 

 

 

 

Increase water button 

 

This washing machine is programmed to use a certain quantity of 
water and consume a certain amount of power considered to be 
sufficient for a normal washing cycle. 

Only press this button for specific requirements

,

 

e.g.: for very 

delicate fabrics (curtains or wool). 

The water level for washing and rinsing rises and 

power 

consumption for heating increases. 

 

 

 

 

Easy-iron button 

 

This option reduces creasing on garments at the end of the 
programme. The machine performs a more delicate spin cycle and 
moves the garments at the end of the programme. Spin speed for 
all programmes is 600 rpm. 

 

 

 

 

Economy cycle button 

 

Press this button for cottons programmes, 

the machine will 

perform an extended wash at 35°C (biological step) thereby 
offering good washing performance combined with power 
saving. 

The machine then continues the cycle at the selected 
temperature. 

 

N.B.:

 

Press the 

economy cycle

 button to obtain a maximum washing 

temperature of 60° C. 

 

 

 

 

Extra Rinse button 

 

In areas with soft water or to improve rinsing, press this button 
(optional for intensive programmes) to enable the extra rinse 
function (about 20% more water). 

 

 

 

 

 

No spin button 

  

 

Press this button to eliminate the final spin cycle. The machine 
stops with the tub full of water and the washing remains soaked. To 
remove the soaked and dripping washing (drip-dry fabrics) turn the 

knob to the drain and spin position (Drain 

) and press the 

“Start/Pause” button. The water is automatically drained on all 
programmes without spinning.  

 

 

 

 

Delicates button 

 

Press this button to reduce movement of the drum and, 
consequently, of the washing. Suitable for particularly delicate 
garments (shirts, silk, curtains, etc.) 

 

 

 

 

Half load button 

1/2 

If the machine is used with a smaller amount of washing than that 
indicated in the “Programme Chart”, press this button to save water, 
detergent and electricity. 

This option should not be used for synthetics or woollens. 

The recommended doses of detergents should be reduced in 
proportion to the load. 

 

 

 

 

 

 

 

 

 

 

 

Summary of Contents for SLB600























Reviews: