background image

 

 

-2- 

INDEX 

1.

 

GENERAL INFORMATIONS .................................................................................................................................... 3

 

1.1.

 

MANUFACTURER / ASSISTANCE ............................................................................................. 3

 

1.2.

 

CERTIFICATION ................................................................................................................ 3

 

1.3.

 

PURPOSE OF THE MANUAL AND ITS CONTENTS ........................................................................... 3

 

1.4

 

CARE AND STORAGE OF THE MANUAL ...................................................................................... 3

 

1.5.

 

IMPORTANT SYMBOLS TO REMEMBER ....................................................................................... 3

 

2.

 

CHARACTERISTICS OF THE DEVICE .................................................................................................................... 4

 

2.1.

 

RECOMMENDED USE ........................................................................................................... 4

 

2.2.

 

SCHEMATIC REPRESENTATION ............................................................................................... 4

 

2.3

 

COMPONENTS .................................................................................................................. 5

 

2.4

 

DESCRIPTION .................................................................................................................. 5

 

2.5

 

TECHNICAL SPECIFICATIONS ................................................................................................. 6

 

2.5

 

GENERAL DIMENSIONS ........................................................................................................ 7

 

2.6

 

INTERNAL LAYOUT ............................................................................................................ 7

 

3.

 

INSTALLATION ........................................................................................................................................................ 8

 

3.1

 

DISHWASHER REAR SIDE INSTALLATION .................................................................................... 9

 

3.2

 

DRAIN FITTING EN1717 ....................................................................................................... 9

 

3.3

 

EXTERNAL PREFILTER INSTALLATION ...................................................................................... 10

 

3.4

 

DRAIN CAPILLARY REPLACEMENT .......................................................................................... 11

 

4.

 

FUNCTIONING ........................................................................................................................................................ 12

 

4.1

 

FIRST START-UP .............................................................................................................. 12

 

4.2

 

NORMAL USE .................................................................................................................. 12

 

4.3

 

LOW PRESSURE ALARM ...................................................................................................... 12

 

4.4

 

LEACKAGE ALARM ............................................................................................................ 12

 

4.5

 

INACTIVITY .................................................................................................................... 12

 

5.

 

ENDUSER ORDINARY MAINTENANCE ................................................................................................................ 13

 

5.1

 

FILTER REPLACEMENT ....................................................................................................... 13

 

6.

 

PROFESSIONAL EXTRAORDINARY MAINTENANCE ......................................................................................... 14

 

6.1.

 

REQUIRED TRAINING FOR MAINTENANCE PERSONNEL ................................................................... 14

 

6.2.

 

RESPONSIBILITIES OF MAINTENANCE PERSONNEL ........................................................................ 14

 

6.3

 

POWER CORD / POWER PLUG REPLACEMENT ............................................................................ 14

 

6.4

 

CHECK/REPLACEMENT OF OSMOTIC MEMBRANES ........................................................................ 15

 

6.5

 

PUMP REPLACEMENT ........................................................................................................ 16

 

6.6

 

CLEANING SOLENOID VALVE FILTER / SOLENOID VALVE REPLACEMENT .............................................. 17

 

6.7

 

MACHINE SANITATION ....................................................................................................... 18

 

6.8

 

FUSE REPLACEMENT / ELECTRONIC BOARD REPLACEMENT ............................................................. 19

 

6.9

 

VERIFICATION OF THE PRESSURE SETTINGS .............................................................................. 20

 

7

 

TROUBLESHOOTING ............................................................................................................................................ 21

 

ATTACHMENT I – CE LABEL ......................................................................................................................................... 24

 

ATTACHMENT II – MAINTENANCE LOG ....................................................................................................................... 24

 

Summary of Contents for WO-02

























Reviews: