background image

AirVerter

® 

Stencil Pro HVLP Paint Spray System

DO NOT OPERATE SPRAY GUNS WITHOUT PERSONAL SAFETY EQUIPMENT

Why AirVerter

 Spray Gun Systems Work Better

To accomplish effective atomization of a liquid at low pressure (below 10 PSI) it is necessary to
substantially decrease pressure (PSI) and increase air volume (CFM). AirVerter

®

 systems, by design, do

not exceed 10 PSI at the spray head and prevent the operator from taking AirVerter

®

 spray guns out of

compliance with EPA and California’s South Coast Air Quality Management District (SCAQMD)
regulations.

Please Read This Owner’s Manual 

BEFORE

Using Your Stencil Pro Spray Gun

DO NOT OPERATE THIS EQUIPMENT WITHOUT USING PROPER
PERSONAL SAFETY EQUIPMENT INCLUDING RESPIRATOR, GOGGLES
AND SAFETY CLOTHING. OBSERVE ALL PRECAUTIONS RELATED TO
SPRAYING.

WARNING

THIS EQUIPMENT IS OPERATED USING PRESSURIZED AIR.  ALWAYS
DISCONNECT SPRAY GUN FROM AIR AND FLUID HOSES AND
DEPRESSURIZE SYSTEM PRIOR TO ANY MAINTENANCE OR
DISASSEMBLY PROCEDURE.

WARRANTY

Smith Eastern Corporation warrants to the Purchaser that the Stencil Pro (CT-100) Spray Gun is
free from defects in material or workmanship under normal use and service for a period of twelve
(12) months from the date of purchase.  Should any failure appear during this period, Smith
Eastern shall, if given prompt written notice by the Purchaser, correct such nonconformity by repair
or replacement of the nonconforming part, F.O.B. Smith Eastern’s repair facility.  Repair parts are
warranted for ninety (90) days from the date of shipment, but repairs or replacements to original
equipment shall not renew or extend the warranty period of such equipment.  Equipment and parts
furnished by Smith Eastern but manufactured by others shall be limited to the warranty offered by
the manufacturer thereof.

Smith Eastern reserves the right to limit this warranty in cases of misuse or abuse.  Any
modifications to spray guns or recommended procedures will void the warranty.

The foregoing warranty is exclusive and in lieu of other warranties of quality or performance,
expressed, implied or statutory, including any warranties of merchantability or of fitness for a
particular purpose.

Summary of Contents for AirVerter Stencil Pro CT-100













Reviews: