7
Ser
vice
SERVICE CHART
Before servicing or making adjustments to the machine, stop engine, set park break, block
wheels and remove key from ignition.
Follow all procedures and ONLY use parts prescribed by the manufacturer. Read the engine
manual before maintenance.
Maintenance Service Interval
Maintenance Procedure
Torque the wheel lug nuts. (64-74 ft/lb (87-100 Nm))
Change the engine oil and filter.
After the first 20 operating hours
Replace hydraulic filter
Check the engine oil.
Check the hydraulic fluid level.
Check the tire pressure.
Check fuel level
Check condition of hydraulic hoses and fittings.
Inspect and clean the machine.
Flush spray system tank.
Inspect cooling system.
Change the engine oil and filter.
Check hydraulic filter
Check engine for leaks or loose parts.
Check spark plugs
Check air cleaner.
Check tire pressure (20 psi (1.4 bar)).
Check the battery fluid level and cable connections.
Torque the wheel lug nuts. (64-74 ft/lb (87-100 Nm))
Grease Machine.
Check belt tension (where needed)
Change oil filter
Torque the wheel lug nuts. (64-74 ft/lb (87-100 Nm))
Check Idle Speed
Change hydraulic filter
Clean battery terminals
Every 400 hours
Check spark plugs
Lubricate machine
Visual inspection of machine and hydraulic hoses
Change oil.
Torque lug nuts.
Check battery terminals and electrolyte level.
Change all filters.
After the first 5 operating hours
Before each use daily
Every 100 hours
Every 250 hours
Every 500 hours or yearly
Every 200 Hours
Summary of Contents for 10-100-C
