Smithco 20-700-A Parts & Service Download | Manualshive

Page: 4 / 120

background image

2

Introduction

SAFE PRACTICES

1. It is your responsibility to read this manual and all publications associated with this machine.
2. Never allow anyone to operate or service the machine or its optional equipment without proper training

and instructions. Never allow minors to operate any equipment.

3. Learn the proper use of the machine, the location and purpose of all the controls and gauges before

you operate the equipment. Working with unfamiliar equipment can lead to accidents.

4. Wear all the necessary protective clothing and personal safety devises to protect your head, eyes, ears,

hands and feet. Operate the machine only in daylight or in good artificial light.

5. Inspect the area where the equipment will be used. Pick up all debris you can find before operating.

Beware of overhead obstructions and underground obstacles. Stay alert for hidden hazards.

6. Never operate equipment that is not in perfect working order or without decals, guards, shields, or other

protective devices in place.

7. Never disconnect or bypass any switch.
8. Carbon monoxide in the exhaust fumes can be fatal when inhaled, never operate a machine without

proper ventilation.

9. Fuel is highly flammable, handle with care.

10. Keep engine clean. Allow the engine to cool before storing and always remove the ignition key.
11. Disengage all drives and set park brake before starting the engine.

12. Never use your hands to search for oil leaks. Hydraulic fluid under pressure can penetrate the skin and

cause serious injury.

13. This machine demands your attention. To prevent loss of control or tipping of the vehicle:

A.  Use extra caution in backing up the vehicle. Ensure area is clear.
B.  Do not stop or start suddenly on any slope.
C.  Reduce speed on slopes and in sharp turns. Use caution when changing directions on slopes.
D.  Stay alert for holes in the terrain and other hidden hazards.

14. Before leaving operator’s position:

A. Disengage all drives.
B. Set park brake.

C. Shut engine off and remove the ignition key.

D. If engine has to run to perform any maintenance keep hands, feet, clothing and all other parts of

body away from moving parts.

15. Keep hands, feet and clothing away from moving parts. Wait for all movement to stop before you clean,

adjust or service the machine.

16.  Keep the area of operation clear of all bystanders.
17.  Stop engine before making repairs/adjustments or checking/adding oil to the crankcase.
18.  Use parts and materials supplied by

Smithco

only. Do not modify any function or part.

19. Use caution when booms are down as they extend out beyond the center line of the machine.

20. The tank is a confined space, take precaution.

These machines are intended for professional maintenance on golf courses, sports turf, and any other

area maintained turf and related trails, paths and lots. No guaranty as to the suitability for any task is

expressed or implied.

«
...
2
3
4
5
6
...
»

Summary of Contents for 20-700-A

























































































































Reviews:

No comments

Related manuals for 20-700-A

Brand: Fast Pages: 112

Brand: WAGNER Pages: 40

Brand: B&G Pages: 4

Brand: Ozito Pages: 8

Brand: O3 Waterworks Pages: 12

Brand: Agrimate Pages: 16

ST Max 395 Hopper

Brand: Graco Pages: 40

Brand: Binks Pages: 12

Brand: EINHELL Pages: 154

Brand: Jacto Pages: 92

Brand: WAGNER Pages: 72

Brand: ZEP Pages: 6

Brand: Kärcher Pages: 332

Brand: Sagola Pages: 36

Brand: Parkside Pages: 104

Brand: maltech Pages: 35

Brand: WAGNER Pages: 12

Brand: Ruris Pages: 113

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands