background image

 

 
No Routine Maintenance is required.  
 
Thoroughly clean of the entire unit by flushing the internal 
components (see clean up on page 11) and the exterior 
surfaces.

 

 

   

 

C A U T I O N

   

 

 

 

Service on this unit both within and after the warranty 
period should be performed only by an authorized service 
center. To find the service center nearest 
you Call 1-515-202-0052 

 
 

 

For a list of replaceable parts, please call 515-202-0052 for 
assistance. 

 

 
 
 
 
 
 
 
 
 
 
 
 

Page 13 

Safety Information 

 

Introduction 

 

  

This Safety Alert Symbol is used to call attention to 

items or operations which may be dangerous to those 
operating or working with this equipment. The symbol can 
be found throughout this manual. Please read these 
warning and cautions carefully before attempting to 
operate the unit. Make sure every individual who operates 
or works with this equipment is familiar with all safety 
precautions. 
 

   

 

W A R N I N G

 

 

 

 

GENERAL WARNING:  Indicates information important to 
the proper operation of the equipment. Failure to observe 
may result in damage to the equipment and/ or severe 
bodily injury or death. 
 
 

   

 

C A U T I O N

   

 

 

GENERAL CAUTION:  Indicates information important to 
the proper operation of the equipment. Failure to observe 
may result in damage to the equipment. 
 

REFERENCES:  For details on safety rules and regulations in the United States, contact 
your local Occupational Safety and Health Administration (OSHA) office. Equipment 
operated in other countries must be operated and serviced in accordance and 
compliance with any an all safety requirements of that country. The publication of these 
safety precautions is done for your information. SMK does not by the publication of these 

precautions imply or in any way represent that these are the

 

sum of

 all dangers present 

n

ear

 

SMK equipment. If you are operating SMK equipment, it is your responsibility to 

insure that such operation is in full accordance with all applicable safety requirements 
and codes. All requirements of the United States Federal Occupational Safety and 
Health Administration Act must be met when operated in areas that are under the 
jurisdiction of the United States Department. 

 

  

 

 
 

Page 2 

 

Maintenance 

Service

 

Replacement Parts

 

Summary of Contents for P100AC









Reviews: