background image

 

15 

C

OMPUTER

 D

ISPLAY

” 

 

Workout Data Ranges 

Time 

00:00 to 99:59 Min 

Speed 

0.0 to 999.9MPH 

Distance 

0.00 to 999.9Mi 

Calories 

0 to 9999 Cal 

Pulse 

40 to 240 BPM 

 

C

OMPUTER

 D

ISPLAY

 O

PERATION

” 

 
Selecting the Data on the Display 
Press the selection button to display the preferred data reading. The selection 
symbol will highlight the current data being displayed.   
 
Scan   
When scan is highlighted the computer will display each of the seven data 
readings in sequence. Each data reading will be displayed for approximately 5 
seconds before displaying the next data reading. 
 
Auto On 
To turn the bike on simply press the selection button or begin to pedal the bike. 
 
Auto Shut Off 
The computer will automatically shut off when the bike is left inactive for 4 
minutes. 
 
Pulse 
To operate the pulse feature simply place your hands over the silver hand grips 
on the handle bars. The heart rate will be displayed in approximately 10 seconds 
or less 
 
 
 

T

ROUBLE SHOOTING

” 

 
Symptom 

Solution 

Computer does not 

function 

Make sure all computer connections are properly 
connected.   
Replace the batteries 

Seat is not stable 

Check that the seat pin is locked in place 
Check that the seat knob is tightened completely 

Seat will not adjust 

Loosen the seat knob 

Summary of Contents for SMB-XBIKE




















Reviews: