background image

1 YEAR LIMITED WARRANTY

Express and Exclusive Limited Warranty to Original Retail Buyer
Alltrade Tools LLC (hereinafter "Alltrade") expressly warrants to the original retail
purchaser of the accompanying SNAP-ON™ portable air tool and no one else all
parts of the product (except those parts referred to below which are specifically
excluded from such warranty (see Exclusions) to be free from defects in materials
and workmanship for a period of one year from the original date of purchase.

The date of purchase shall be the date of shipment to the original purchaser, or the
date the original purchaser took possession, custody, or control of the product,
whichever occurred first. This warranty shall be null and void if the product or any
component thereof is modified or altered. This warranty does not apply to any other
product and/or component thereof manufactured or distributed by Alltrade, and
does not apply to products and/or components thereof designed, manufactured
and/or assembled by others, for which Alltrade makes no warranties whatsoever.
THERE ARE NO WARRANTIES, WHICH EXTEND BEYOND THE DESCRIPTION ON
THE FACE HEREOF.

WARRANTY PERFORMANCE
By purchasing this product, purchaser expressly acknowledges and agrees that
their sole and exclusive remedy under this warranty shall be strictly limited to the
repair or replacement of any covered nonconforming items or parts thereof provid-
ed that any such nonconforming item and/or part is promptly returned to an author-
ized Service Center within the applicable warranty period, with a written request by
purchaser to repair and/or replace the nonconforming item and/or part. We recom-
mend that you keep the original product packaging in the event you need to ship the
unit. We suggest the package be insured against loss or in transit damage. When
sending your product, include your name, address, phone number, e-mail address,
dated proof of purchase (or copy) and a statement about the nature of the problem.
Warranty coverage is conditioned upon purchaser furnishing Alltrade with adequate
written proof that they are the original purchaser and of the original purchase date.
Parts returned, freight prepaid and insured, will be inspected and, at Alltrade's
option, repaired and/or replaced free of charge if it is found to be defective and sub-
ject to warranty. Alltrade retains the sole discretion to determine whether any item
or part is nonconforming and, if so, whether the item and/or part will be repaired
and/or replaced. If the unit is repaired, new or reconditioned replacement parts may
be used. If Alltrade chooses to replace the product, it may replace it with a new or
reconditioned of the same or comparable design. The repaired or replaced unit will
be warranted under the terms of the remainder of the one year warranty period; cov-
ered defective parts not subject to normal wear and tear or other exclusions will be
repaired or replaced, at Alltrade's option. During the warranty period, Alltrade will
be responsible for the return shipping charges. Alltrade's repair and/or replacement
of any nonconforming item and/or part thereof shall constitute fulfillment of all obli-

26

ITEM NO.

PART NO.

DESCRIPTION

SPECIFICATIONS

25

75

A0000-0681

BHSC Screw M5*10

76

A0000-0061

Screw M5*12

77

K0700-4741

Magazine Set

78

A0003-0221

Rivet

79

A0718-0561

Magazine Cover

80

A0105-0191

Nail Detainer

81

A0701-2431

Rail Magazine

82

K0700-4771

Pusher Assembly

83

A0102-0071

Spring

84

A0703-0151

Roller, Negator Spring

85

A0005-0311

Pin Retainer 5.5*2

86

A0707-1741

Feeder Clip

87

A0100-1081

Spring

88

K0700-4751

Pusher Set

89

A0006-1351

Pin

MODEL NUMBER

870011

AIR PRESSURE

70-120 PSIG (5.0- 8.5 kg/cm

2

G

NAIL LENGTH

2" (50.8 mm) - 3 1/2" (88.9 mm)

COLLATION ANGLE

30-34°

MINIMUM HOSE
DIAMETER

1/4" (6.5 mm)

NET WEIGHT

7.2 LBS. (3.2 KG)

Summary of Contents for 870011
















Reviews: