background image

WAIVES ANY AND ALL SUCH WARRANTIES AND RIGHTS, CLAIMS AND/OR
CAUSE OF ACTION ARISING THEREFROM OR BASED THEREON. PURCHASER'S
SOLE AND EXCLUSIVE REMEDY IS AS STATED ABOVE.

EXCLUSION AND DISCLAIMER OF ALL IMPLIED WARRANTIES, INCLUDING THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. NO WARRANTY, ORAL OR WRITTEN, OTHER THAN THE WARRANTY
LISTED HEREIN IS MADE WITH REGARD TO THIS PRODUCT. ALL WARRANTIES
AND/OR IMPLIED WARRANTIES, GUARANTIES AND/OR REPRESENTATIONS BY
ALLTRADE AND/OR ITS REPRESENTATIVE(S) REGARDING THE DESIGN, MANU-
FACTURE, PURCHASE, USE AND/OR OPERATION OF THE PRODUCT OR ANY COM-
PONENT THEREOF SOLD HEREUNDER, REGARDLESS OF WHETHER ANY SUCH
WARRANTY, GUARANTY AND/OR REPRESENTATION, WRITTEN OR ORAL, ARISES
BY OPERATION OF LAW AND/OR EQUITY AND/OR BY ANY ACT OR OMISSION OF
ALLTRADE AND/OR ITS REPRESENTATIVES. PURCHASER KNOWINGLY AND
WILLINGLY WAIVES ANY AND ALL SUCH WARRANTIES AND RIGHTS, CLAIMS
AND/OR CAUSES OF ACTION ARISING THEREFROM OR BASED THEREON.

PURCHASER'S SOLE AND EXCLUSIVE REMEDY IS AS STATED ON PRECEDING
PAGES.

LIMITATIONS OF LIABILITY
IN NO EVENT SHALL ALLTRADE AND/OR ITS REPRESENTATIVE(S) BE LIABLE FOR
INDIRECT, INCIDENTAL, SPECIAL AND/OR CONSEQUENTIAL DAMAGES OF ANY
KIND ARISING OUT OF OR RELATED TO, DIRECTLY OR INDIRECTLY, ANY BREACH
OR PROVISION OF ANY AGREEMENT BETWEEN ALLTRADE AND/OR ITS REPRE-
SENTATIVE(S) AND PURCHASER, AND WARRANTY HEREUNDER, AND/OR THE
EXISTENCE, DESIGN, MANUFACTURE, PURCHASE, USE AND/OR OPERATION OF
ANY ITEM(S) SOLD HEREUNDER EVEN IF ALLTRADE AND/OR ITS REPRESENTA-
TIVE(S) HAS BEEN ADVISED OF THE POSSIBILITY OF ANY SUCH DAMAGES. IN NO
EVENT, WHETHER BECAUSE OF A BREACH OF CONTRACT, WARRANTY, TORT
(INCLUDING NEGLIGENCE) OR OTHERWISE, SHALL ALLTRADE'S AND/OR ITS
REPRESENTATIVE (S) LIABILITY EXCEED THE PRICE OF THE PRODUCT. All LIA-
BILITY CONNECTED WITH THE USE OF THIS PRODUCT SHALL TERMINATE UPON
THE EXPIRATION OF THE WARRANTY PERIODS SPECIFIED ABOVE.

LIMITATIONS ON WARRANTY DISCLAIMERS
Some states do not allow limitations on how long an implied warranty lasts and
some states do not allow the exclusion or limitation of the incidental or consequen-
tial damages, so part or all of the above limitations or exclusions may not apply to
you. This warranty gives you specific legal rights, and you may also have other
rights, which vary from state to state.

If your product is not covered by this warranty, please call our Customer Service
Department at 1-888-278-8092 for general repair information, and charges and the
location of your nearest authorized service facility.

28

gations to the purchaser. Alltrade shall not be responsible or liable for any expense,
including freight charges, or repairs made outside Alltrade's facility or an Alltrade
designated service, unless expressly agreed to by Alltrade in writing. Under no cir-
cumstances shall Alltrade bear any responsibility for loss of the unit, loss of time or
rental, inconvenience, commercial loss, or consequential damages.

For the location of an Authorized Service Center nearest you, please call customer
service at 1-888-278-8092.

EXCLUSIONS
Air nailers and staplers need periodic maintenance to remain in proper operating
condition. Normal wear parts (o-rings and driver blades) shall be warranted to the
original purchaser to be free from defects in materials and workmanship for a peri-
od of 90 days from the original date of purchase.

This warranty does not cover parts damaged due to normal wear, abnormal condi-
tions, misapplication, misuse, abuse, accidents, operation, improper storage, or
freight damage. Parts damaged or worn by operation in dusty environments are not
warranted. Failure to follow recommended operating and maintenance procedures
also voids warranty.

DAMAGE TO THE PRODUCT RESULTING FROM TAMPERING, ACCIDENT, ABUSE,
NEGLIGENCE, FAILURE TO FOLLOW INSTRUCTIONS, UNAUTHORIZED REPAIRS
OR ALTERATIONS, DAMAGE WHILE IN TRANSIT TO OUR SERVICE FACILITY, USE
OF UNAPPROVED OR IMPROPER ATTACHMENTS OR ACCESSORIES, OR OTHER
CAUSES UNRELATED TO PROBLEMS WITH MATERIAL OR WORKMANSHIP ARE
NOT COVERED BY THIS WARRANTY.

Alltrade will not be liable for the following: labor charges, loss or damage resulting
from improper operation, maintenance or repairs made by other persons; pre-deliv-
ery services such as assembly, oil and lubricants, and adjustment; maintenance
services that are normally required to maintain the product.

The use of other than genuine Snap-On™ Repair Parts will VOID the warranty.

WARRANTY DISCLAIMERS
EXCLUSION AND DISCLAIMER OF ALL OTHER EXPRESS WARRANTIES, GUAR-
ANTIES AND/OR REPRESENTATIONS, EXCEPT FOR THE LIMITED WARRANTY
PROVIDED HEREIN, ALL OTHER EXPRESS WARRANTIES, GUARANTIES, AND/OR
REPRESENTATIONS BY ALLTRADE AND OR ITS REPRESENTATIVE(S) REGARDING
THE DESIGN, MANUFACTURE, PURCHASE, USE AND/OR OPERATION OF THE
PRODUCT OR ANY COMPONENT THEREOF SOLD HEREUNDER, REGARDLESS OF
WHETHER ANY SUCH WARRANTY, GUARANTY AND/OR REPRESENTATION,
WRITTEN OR ORAL, ARISES BY OPERATION OF LAW AND/OR EQUITY AND/OR BY
ANY ACT OR OMISSION OF ALLTRADE AND/OR ITS REPRESENTATIVE(S), OR THE
BUYER, ARE HEREBY EXPRESSLY EXCLUDED AND DISCLAIMED BY ALLTRADE
AND/OR ITS REPRESENTATIVES. PURCHASER KNOWINGLY AND WILLINGLY

27

Summary of Contents for 870011
















Reviews: