Snap-On ControlTech CTLNK1R240 Manual Download

Page: 15 / 36



Advanced Settings

Accessing Advanced Settings

Advanced settings are accessed from

SETTINGS

menu selection on main menu.

From target torque or angle screen, press and hold ENTER button for 3 seconds.

Highlight

SETTINGS

menu selection using UP/DOWN buttons.

Press ENTER button to display Settings menu.
Menu Selections:



EXIT - Exits Settings menu and returns to target screen.



SHOW INFO - Displays wrench operational information.



SLEEP TIME - Displays power down interval setup screen.



LCD CONTRAST - Displays LCD contrast setup screen.



KEY BEEP - Displays button press beep enable/disable setup screen.



AUTO BACKLIGHT - Displays auto backlight enable/disable screen to turn on backlight during
measurement.



TOGGLE BACKLGHT - Displays BACKLIGHT button toggle or timeout enable/disable screen.



VIBRATOR CONFIG - Displays vibrator ON/OFF configuration for when target reached.

To exit Settings menu and return to target torque or angle screen, press ENTER button while

EXIT

selection is highlighted.

Note: All user configurable settings are stored in non-volatile memory and are retained while

power is off.

Show Info

Show Info menu selection displays wrench operational information.

From Settings menu, press ENTER button while

SHOW INFO

selection is highlighted.

SHOW INFO screen is displayed.

UP/DOWN buttons are used to scroll screen.
Operational Information:



SN: Serial number assigned to wrench.



CAL: Date of last wrench calibration.



ISD: In-Service Date.



TCF: Torque Calibration Factor.



ACF: Angle Calibration Factor.



VER: Software version.



OVR CNT: Overtorque Counter tracks how many times an over-torque event occurred on wrench
(torque >125% of full scale).



TQZ: Torque Zero Offset.



ANZ: Angle Zero Offset.

Pressing ENTER button exits Show Info screen and returns to Settings menu.

Settings menu

100.0

FT-LB

Target Screen

SHOW DATA

CLEAR DATA

CYCLE COUNT

SETTINGSs

UP/DOWN buttons

ENTER
button

EXIT

LANGUAGE

SET HEAD LENGTH
SHOW DATA

ENTER
button

held

EXIT

SHOW INFO

SLEEP TIME
LCD CONTRAST

Summary of Contents for ControlTech CTLNK1R240





































Search results

Summary of Contents for ControlTech CTLNK1R240

Reviews:

Related manuals for ControlTech CTLNK1R240

Brands by name

Popular brands

Snap-On ControlTech CTLNK1R240, Manual

Search results

Summary of Contents for ControlTech CTLNK1R240

Reviews:

Related manuals for ControlTech CTLNK1R240

Brands by name

Popular brands