Snap-On ControlTech CTLNK1R240 Manual Download | Manualshive

Page: 25 / 36

background image

Job Mode

Job Mode function allows user to enable or disable wrench preset Job mode. When in Job mode, wrench
executes presets in order configured and automatically switches to next preset when batch count reaches zero.
Wrench is locked and Preset lock icon is displayed when Job mode is enabled.

Note: Password entry is required to enable Job Mode. When enabled, password entry is required to re-enter

Configure menu (refer to ControlTech™ Calibration manual for default password).

1.

From Configure menu, use UP/DOWN buttons to highlight

JOB MODE

selection then press ENTER button.

2.

Job Mode enable/disable screen is displayed.

3.

Use UP/DOWN buttons to select ENABLE or DISABLE.

4.

Press ENTER button to accept selection and exit to Configure menu.

Note: Text "JOB" is displayed between PSET number and batch count when enabled.

Calibration

Calibration menu is password protected. Refer to ControlTech™ Calibration manual.

Setting Date and Time

Set Date/Time function allows user to set real-time-clock date and time for time stamping data records,
recording last calibration date and notifying user of an expired calibration interval.

Note: When date and time is set for first time, In-Service date is also set and is used for calculating initial

calibration interval (see "Setting Calibration Interval" in Advanced Configuration section).

1.

From Configure menu, use UP/DOWN buttons to highlight

SET DATE/TIME

selection then press ENTER

button.

2.

SET DATE screen is displayed with year highlighted.

3.

Use UP/DOWN buttons to set year then press ENTER button to highlight month.

4.

Use UP/DOWN buttons to set month then press ENTER button to highlight day.

5.

Use UP/DOWN buttons to set day then press ENTER button.

PSET 01

JOB

00

100.0

FT-LB

PRESET LOCK

  DELETE PRESETS
  JOB MODE

CALIBRATION

ENTER PASSWD

0

0

0

0

0

Password screen

UP/DOWN buttons

ENTER

button

UP/DOWN buttons

JOB MODE

ENSABLE

DISABLE

ENTER

button

UP/DOWN buttons

JOB MODE

ENABLE

DISABLE

ENTER

button

ENTER

button

EXIT

MODE SETUPs

PRESET LOCK
DELETE PRESETS

Job Mode menu

MODE SETUP

PRESET LOCK
DELETE PRESETS

JOB MODE

MODE SETUP

PRESET LOCK
DELETE PRESETS

JOB MODE

EXIT

MODE SETUP

DELETE PRESETS

JOB MODE

Lock icon

«
...
23
24
25
26
27
...
»

Summary of Contents for ControlTech CTLNK1R240





































Reviews:

No comments

Related manuals for ControlTech CTLNK1R240

Brand: Vector Pages: 6

Brand: National Flooring Equipment Pages: 23

Brand: RAMSET Pages: 16

Brand: B&B Electronics Pages: 2

CYBERCORE PLATINUM Series

Brand: XPG Pages: 50

Brand: First Choice Pages: 2

Brand: Tool Connection Pages: 2

Brand: KABI Pages: 6

Brand: Gardner Denver Pages: 27

PSI 9000 Series

Brand: Electro-Automatik Pages: 64

XTRIC 363000 80S

Brand: GARANT Pages: 116

Brand: H3C Pages: 8

Brand: 3B SCIENTIFIC PHYSICS Pages: 24

Brand: Greenlee Pages: 12

Brand: Delta Pages: 4

Brand: Centro Pages: 8

Brand: Gern Pro Pages: 25

Brand: SATA Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands