background image

GENERATOR CAPACITY AND APPLIANCE WATTAGE

Ensure generator can supply adequate rated (running) and surge (starting) wattage
for devices it will power at same time. Follow the steps below:

1. Select all devices that will be powered at the same time.

2. Total rated running watts of devices. This is amount of power the generator

must produce to keep devices running. See table below.

3. Estimate amount of surge (starting) wattage needed. Surge wattage is a short

burst of power needed to start electric motor-driven tools and appliances such
as an electric compressors, pumps, drills or refrigerators. Because not all
motors start at same time, total surge wattage can be estimated by adding only
the item(s) with highest additional surge watts to the total rated watts as
described below.

EXAMPLES OF RATED AND SURGE WATTAGE

TOOL OR APPLIANCE

Total Rated (Running) Watts

= 2500

Highest Additional Surge Watts

= 2400

Total Generator Output Required

= 4900

Never add more loads to generator than it has capacity for. Take additional
care to consider surge loads in generator capacity.

Exceeding generator load

limit can result in damage to unit and to appliances or tools connected to it.

Exceeding generators wattage/amperage capacity can damage generator
and/or any electrical devices connected to it.

Improper treatment of generator can damage internal components and 
shorten the life of unit.

Exhaust heat/gases can ignite combustible materials, structures or
damage to fuel tank resulting in fire.

Keep at least 5 ft. (1.5 m) 

clearance on all sides of generator including overhead.

DO NOT

exceed wattage/amperage capacity. See “Generator Capacity” section of

this manual.

• If connected devices overheat, turn them 

OFF

and disconnect them from generator.

• Use a ground fault circuit interrupter (GFCI) anywhere dampened or highly 

conductive areas, such as metal decking or steel work.

DO NOT

touch bare wires or outlets. Severe burns or even death can result.

DO NOT

use generator with electrical cords which are worn, frayed, bare or 

otherwise damaged.

DO NOT 

handle generator or electrical cables while standing in water, while

barefoot or whenever hands and feet are wet.

DO NOT

connect 3-phase loads to generator.

DO NOT

connect 50 Hz loads to generator.

• Always connect electrical loads to generator while the load is turned 

OFF

. After

connecting loads to generator, turn the load 

ON

.

• Always turn electrical loads 

OFF

and disconnect them from generator before

stopping generator engine.

24

23

Tool or Appliance

Rated (Running) Watts

Additional Surge

(Starting) Watts

Window Air Conditioner

1200

1800

Refrigerator

800

1600

Television

500

Summary of Contents for SR3000






















Reviews: