background image

14

TROUBLE

CAUSE

REMEDY

Engine will not
start.

1. ON/OFF switch in

OFF position.

2. Engine flooded.

3. Fuel tank empty.
4. Spark plug not firing.
5. Fuel not reaching

carburetor.

6. Carburetor requires

adjustment.

1. Move ON/OFF switch to ON.

2. See “Starting a Flooded Engine” in

Operation Section.

3. Fill tank with correct fuel mixture.
4. Install new spark plug.
5. Check for dirty fuel filter; replace.

Check for kinked or split fuel line;
repair or replace.

6. Contact an authorized service dealer.

Engine will
not idle
properly.

1. Carburetor requires

adjustment.

2. Crankshaft seals worn.
3. Compression low.

1. See “Carburetor Adjustment” in

Service and Adjustments Section.

2. Contact an authorized service dealer.
3. Contact an authorized service dealer.

1. Air filter dirty.
2. Spark plug fouled.

3. Carburetor requires

adjustment.

4. Carbon build-up on

muffler outlet screen.

5. Compression low.

Engine will not
accelerate,
lacks power,
or dies under
a load.

1. Clean or replace air filter.
2. Clean or replace plug

and regap.

3. Contact an authorized service dealer.

4. Contact an authorized service dealer.

5. Contact an authorized service dealer.

Engine
smokes
excessively.

1. Choke partially on.
2. Fuel mixture incorrect.

3. Air filter dirty.
4. Carburetor requires

adjustment.

1. Adjust choke.
2. Empty fuel tank and refill with

correct fuel mixture.

3. Clean or replace air filter.
4. Contact an authorized service dealer.

Engine runs
hot.

1. Fuel mixture incorrect.

2. Spark plug incorrect.
3. Carburetor requires

adjustment.

4. Carbon build-up on

muffler outlet screen.

1. See “Fueling Engine” in Operation

section.

2. Replace with correct spark plug.
3. Contact an authorized service dealer.

4. Contact an authorized service dealer.

WARNING:

Always stop unit and disconnect spark plug before performing all of the

recommended remedies below except remedies that require operation of the unit.

TROUBLESHOOTING TABLE

For Parts Call K&T 606-678-9623 or 606-561-4983

www.mymowerparts.com

Summary of Contents for S31SNG

















Reviews: