background image

Daily Preventative Maintenance Checklist

22 

T40RT/T46JRT – 1430001

ITEM

INSPECTION OR SERVICES

Y

N

R

Operator’s Manual

In place, all pages readable and intact

Engine

Oil level

Between full and add marks

Coolant

Proper fluid level

Radiator

Cap tight, good condition and clean

Fuel tank and line

Tank full, cap in place and tight/ no leaks

Electrical System

Battery

Condition and charged for proper operation

Battery fluid level and terminals

Proper level/clean, connectors tight

Cables and wiring harness

No wear or physical damage

Hydraulic System

Fluid level

Between full and add marks

Hose, tubes and fittings

No leaks

Cold weather warm-up kit

Proper operation

Tires

Good condition

Wheels

All wheel lug nuts present and properly torqued

Lower Control Station

Operating controls

Proper operation

Emergency stop and emergency power

Shuts off lower controls/proper operation

Level Sensor

Sounds tilt alarm

Flashing Light

Proper operation

All Motion Alarm

Sounds when machine is operated and/or driven

Structures

Weldments – 

Chassis, turntable, booms, platform, etc.

Welds intact, no damage or deformation

Slide pads

In place, no damage or deformation

Fasteners

In place and tight.

Upper Control Station

Guardrail system and lanyard anchors

Welds intact, no damage or deformation

Operating controls – 

Boom functions, drive, brakes, etc.

Proper operation

Emergency stop and emergency power

Shuts off upper controls/proper operation

Horn

Sounds when activated

Placards and Decals

In place and readable

Maintenance Table Key: Y = Yes/Acceptable, N = No/Not Acceptable, R = Repaired/Acceptable

Daily Preventative Maintenance Checklist

Preventative Maintenance Report

Date:

Owner:

Model No:

Serial No:

Serviced By:

Summary of Contents for 16GTRD































Reviews: