Chapter 9 – Stowing and Transporting
38
S2770RT IS – 0102094
7. Open the door on the right side of the chassis to
access the manual emergency lowering pump (refer
to Figure 9.2).
Figure 9.2 – Manual Emergency Lowering Pump
8. The pump handle is mounted next to the lower con-
trols. Insert the handle into the pump (refer to Figure
9.2).
9. Pull the brake knob outward and twist to lock in po-
sition.
10. Fully turn the valve counterclockwise until loose.
11. Pump the handle several times until pressurized then
stow the handle.
12. Remove the wheel chocks and use the winch to
position the aerial platform on the transport vehicle.
A
Warning
The aerial platform is free to move when the brakes
are released. Death or serious injury could result.
Re-enable the brakes before operating the aerial
platform.
12. After moving the aerial platform, fully turn the valve
clockwise until tight and twist to unlock the brake
knob.
13. After unloading the aerial platform from the transport
vehicle, verify that the drive system and brakes op-
erate properly before operating the aerial platform.
Hoisting
Use a four point sling arrangement attached to the lifting
lugs when hoisting the aerial platform. Machine damage
can occur if the sling is attached anywhere else.
A
Warning
The potential for an accident increases when the
aerial platform is lifted using improper equipment
and/or lifting techniques. Death or serious injury
A
Danger
Lifting the aerial platform with the forklift forks posi-
tioned improperly can produce enough force to dam-
age machine components. When lifting the machine
from the side, place the forklift forks directly under
the designated lift points.
3. To lift the machine from the side, place the forklift forks
directly under the designated points under the chassis.
4. Do not raise the aerial platform higher than necessary
to transport it. Drive the forklift slowly and carefully
when transporting the aerial platform.
Winching
Use the following procedure to winch the aerial platform
onto the transport vehicle:
1. Position the transport vehicle so the aerial platform
will not roll forward after it is loaded.
2. Remove tools, materials, or other loose objects from
the platform.
3. Drive the machine to the foot of the loading ramp
with the front wheels nearest the ramp. Make sure
the machine is centered with the ramps and that the
steering wheels are straight.
4. Properly stow the aerial platform.
5. Chock the wheels to prevent uncontrolled motion of
the aerial platform.
6. Attach the winch to the tie-down lugs (refer to Figure
9.1) on the front of the chassis.
Figure 9.1 – Front Tie-Down/Lifting Lugs
A
Warning
The aerial platform is free to move when the brakes
are released. Death or serious injury could result.
Re-enable the brakes before operating the aerial
platform.
Tie-Down/Lifting Lugs
Pump
Main Control
Valve Assembly
Brake
Release Knob
Scissor
Lower Knob
Valve
Summary of Contents for S2770RT
