background image

Lit. No. 85757, Rev. 01 

22 

November 15, 2018

TROUBLESHOOTING

NOTE: To prevent leaks, use a thread-sealing 
compound on all threaded connections. Do 
not use Te

fl

 on

®

 tape, as fragments will clog the 

spray nozzles. Clamped connections may require 
periodic retightening.

Problem

Possible Cause

Suggested Solution

Pump doesn't run.

Loose electrical connections.

Check all connections.

Blown fuse.

Replace fuse.

Pump seized.

Replace pump.

Dead (or dying) battery.

Charge or replace battery.

Control shut down.

Poor electrical connections.

Clean or replace connectors. Use dielectric 
grease.

Electrical short.

Check electrical connections. Check for 
bare wires.

Dead (or dying) battery.

Charge or replace battery.

Control failure.

Replace control.

Liquid not spraying.

Empty tank.

Fill tank.

Full strainer.

Clean or replace element.

Pump not running.

Refer to Problem 1 ("Pump doesn't run").

Dead (or dying) battery.

Charge or replace battery.

Obstructed nozzle.

Remove and clean.

Te

fl

 on

®

 is a registered trademark of E. I. du Pont de Nemours and Company.

 WARNING

Always shut vehicle OFF before attempting to 
attach, detach, or service sprayer system.

 WARNING

Do not operate a machine in need of 
maintenance.

Whenever service is necessary, your local 
SnowEx

®

 dealer knows your de-icing system best. 

Take your Accuspray™ De-Icing System to your local 
dealer for any maintenance or service needs on your 
unit. If this is not possible, the Troubleshooting Guide 
below may assist you in identifying the problem.

Preliminary Checks:

•  Make sure that all electrical connections are tight 

and clean.

•  Make sure that nothing is obstructing the nozzles.

 WARNING

Read all warning instructions and safety 
messages before servicing the sprayer.

 WARNING

Always wear safety glasses with side shields 
when servicing sprayer system. Failure to do 
this could result in serious injury to the eyes.

Summary of Contents for Accuspray VSS-1000-1

























Reviews: