background image

L1186             © Trynex International 2008

8 — 24

SP-2400 

Mounting Instructions  

Step 1: 

Use centrally locatedlifting point on spreader frame.  Hang spreader in center of dump body opening, (note) spreader

opening must be level with dump floor.

Step 2: 

Using bolts Provided in kit, mount left and right main angle to spreader frame.

Step 3: 

Mark and trim angles to appropriate width to match tailgate, remount angles to spreader frame.  

  

 

Step 1: 

Secure long leveling rod D-5741 to spinner enclosure through bottom hole in bracket with hair pin clip through hole  

hole in pin (see fig 1)

Step 2: 

Mount  drive leveling bracket D-5738 to frame rail 4” below center of hinge.  Weld or bolt in place (see fig 2)

Step 3: 

Connect D-5740 short leveling rod to drive leveling bracket with hair pin clip.  Align both rods next to each other (see fig2)

and weld togther.

  

 

Step 4: 

Using correct pin size provided in kit for lower latch pin, measure and cut pin to correct length.  Clamping pins in correct location, 

tack weld pins to angles securely and lock lower hinge point.

               

 

Step 5: 

 Using correct pin/ears provided for upper hings point, measure and cut to correct length.  Clamping ears in correct location,

 tack weld securely to the left and right main angles (see page 8-23) and secure upper hinge point.

 

 

 

Step 6: 

Double check that spreader will remove and install with ease.

 

  

 

Step 7: 

If using ears for upper hinge point support, upper gussetts must be welded directly behind mounting ears.

(see page 8-23)

Step 8: 

Complete welding pins and ears to angle fully.

 

Step 9: 

 Remove angles from spreader for paint and reinstall.

Mounting Instructions for self leveling spinner bracket

fig. 1

fig. 2

4 “

Dump Body Hinge (step 2)

Summary of Contents for SP-2400





































Reviews: