background image

3

8. 

Do not disassemble the charger. If the charger requires 

service or repair, contact an authorized Snow Joe

®

 +  

Sun Joe

®

 dealer or call the Snow Joe

®

 + Sun Joe

®

 

customer service center at 1-866-SNOWJOE 

 

(1-866-766-9563). Incorrect reassembly poses a risk of 

electric shock, electrocution or fire.

9. 

To reduce the risk of electric shock, unplug the charger 

from the outlet before cleaning the unit.

10. 

Never attempt to connect two (2) chargers together.

11. 

DO NOT store or use the tool and battery pack in 

locations where the temperature may reach or exceed  

104 ºF (40 ºC). Dangerous storing locations include 

outdoor sheds or metal buildings in the summer.

12. 

The charger is designed to operate on standard 

household electrical power (120 V). Do not attempt to use 

it with any other voltage!

 NOTE:

 The integrated battery is not fully charged out of 

the carton. Read the safety instructions and then follow 

the charging notes and procedures.

13. 

The longest life and best performance can be obtained if 

the integrated battery is charged when the air temperature 

is between 64.4ºF – 75.2ºF (18ºC – 24ºC). Do not charge 

the battery pack when the air temperature falls below 

50ºF (10ºC) or above 104ºF (40ºC). Following these safety 

measures will prevent damage to the battery pack.

14. Do not incinerate the integrated battery even if it is 

seriously damaged or completely worn out. The battery 

can explode in a fire.

Summary of Contents for SUNJOE SJ4VSD













Reviews: