background image

MASTERYS BC

from 15 to 20 kVA

45

ENGLISH

10.6.2 Protection on a UPS without auxiliary mains supply.
Activating UPS protection on the mimic panel: access the 

Configurations menu

 on the mimic panel (see 

the 

Configurations Menu

 under the 

Service Menu

 section of the manual) and set the 

BACKFEED TYPE

 

parameter to 

3.BYPASS-INPUT Common

.

Diagram of Principle.

OPTIONS

10

Note.
The neutral is not disconnected as, even in the event of a single fault on the UPS, it never has high potential 
when the mains and/or auxiliary power supplies are disconnected upstream. This is to prevent transformation 
of the power source to the UPS every time there is a power failure.
Should the Neutral potential be very high due to certain error conditions or due to installations downstream 
(e.g. ground fault not detected and protected, high dispersion of a phase, or the IT system), it will be necessary 
to install either devices that disconnect the Neutral or alternatively a system that detects, signals and protects 
against high neutral/ground potential that could lead to UPS failure.

10.6.2-1

A

UPS

L1

Q1

L2
L3
N

T1

B

M1

L1
L2
L3
N

XB1

BKF card

UPS 3/3 without separate auxiliary supply.

Legend.

 

Distribution panel

B 

Coil remote switch

L1-L2-L3-N 

Input power source 

M1 

Input power terminal board

Q1 

Input power switch

T1 

Remote switch

1

XB1 

Connector on BKF PCB

1

Remote switches - rated current

 

 Model 

T1

 

15 /1 

2 A AC1

 

15 / 

2 A AC1

 

20 /1 

45 A AC1

 

20 / 

45 A AC1

Summary of Contents for Masterys MAS2BC115M+D1

















































Reviews: