background image

17

NETYS PR RACK 1U 

- Ref.: IOMNETPRXX01-GB  02

ENGLISH

11. TECHNICAL SPECIFICATIONS

Models

PR 1000 Rack 1U

PR 1500 Rack 1U

Power (VA)

1000

1500

Power (W)

670

1000

Electrical specifications - Input

Voltage

230 V (default); 220 V, 230 V, 240 V selectable

Frequency

45÷65 Hz, 50/60 Hz auto-sensing

Mains connection

IEC 320 (10 A)

Electrical specifications - Output

Voltage (in Normal Mode with AVR)

Voltage (in Battery Mode)

Same as selected nominal input voltage: 220 V, 230 V, 240 V ±5% (-10% after Battery Low)

Frequency

50/60 Hz

Wave form

Sine wave

Transfer time

2-4 ms (typical)

Normal Mode protections

overload (110% for 3 minutes); shortcircuit protected

Battery Mode protections

overload (110% for 30 seconds); shortcircuit protected

Load connection socket IEC 320

(4) 10 A

Battery

Typical back-up time

12 minutes

Battery recharge

Advanced charging for faster recovery. Approximately 3 hours to 90% usable capacity at 

nominal line and no supplementary power supply load).

Reporting and Communication

Communication interface

RS232 - USB

Ethernet adapter

NET-VISION (TCP/IP & SNMP) optional card

Local communication software

UniVision (management software)

Remote communication software

UniVision Pro (management software)

Data line protection

NTP data line suppressor: RJ45 10 Base T

Environment

Noise level (normal mode)

< 45 dBA (at 1 meter)

Temperature

0÷40 °C (10÷25 °C for optimum battery life)

Environment

Altitude: 2000 m, humidity: 95% non-condensing

Reference standards

(EN) IEC62040-1-1 (safety), EN 62040-2 (EMC), EN 61000-4-5/C62.41:1991 (surge)

Mechanical characteristics

Dimensions (WxDxH mm)

440 x 578 x 44,5

Net weight (kg)

21

23

Summary of Contents for NETYS PR 1000 Rack 1U





















Reviews: