background image

20

If the configuration program is used with an earlier UPS model (with an earlier 
UPS firmware version) that does not support the modification of these settings,
the Options tab will display a reminder of the factory default settings.  These 
cannot be changed.

UPS I

NTELLIGENT 

 C

OMMUNICATIONS

The S4K2U UPS is equipped with an Intellislot

®

 port to provide advanced 

communication and monitoring options.  

MultiLink

 software continually monitors the UPS and can shut down 

your computer or server in the event of an extended power failure.

MultiLink can also be configured for use without the serial cable when the 
Intellislot SNMP/Web Card is installed in the UPS. Additionally, MultiLink 
can be configured to coordinate shutdown across the network with other 
computers running MultiLink when you purchase a MultiLink License Kit. 
For more information about the Intellislot SNMP/Web Card and MultiLink 
License Kits, visit our web site (www.solaheviduty.com) or contact your 
local distributor or Sola/Hevi-Duty representative.

Several option cards are available for use in the Intellislot port of the S4K 
Industrial UPS. The Intellislot SNMP/Web Card provides SNMP and 
web-based monitoring and control of the UPS across the network.

The Intellislot MultiPort 4 Card allows you to install MultiLink software on 
four computers and coordinate shutdown in the event of a power failure.

The Intellislot Relay Card provides five dry contact relay outputs for 
custom wired applications and delivers support for built-in shutdown for 
AS/400 systems.

!

CAUTION
To maintain safety (SELV) barriers and for 
electromagnetic compatibility, signal cables should be 
segregated and run separate from all other power 
cables, where applicable.

Summary of Contents for S4K2U Series









































Reviews: