Solare Datensysteme Solar-Log Components Connection Manual Download | Manualshive

Page: 129 / 506

background image

129

Fronius

32.3

Fronius Symo/Galvo/ECO Series

For the Symo/Galvo/ECO series, Fronius offers two different inverter types:

•

Symo, Galvo and ECO, as well as the light version of the series.

The instructions for wiring the inverters to the Solar-Log™ are identical to those for Fronius inverters with Com-
Card. Refer to the section on „Fronius with ComCard“ for more information.

General information on the Symo / Galvo series

The standard Symo comes equipped with a data manager that acts as a bus master. The data manager has to be
removed to be able to communicate with the Solar-Log™. Since the Fronius Com Card is already integrated in the
Symo and Galvo models, no additional Com Card is required for network interface.
The Datamanager is not integrated into the Symo Light models.

Note

The Symo / Galvo series is pre-configured for the "Solar.Net" protocol.

►

Check the settings if necessary.

Note

With the introduction of Datamanager 2.0, there is the option to set the inverter detection to slave and
then it does not have to be removed.

Note

When connecting a Solar-Log™ with several Fronius inverters via Ethernet, each Fronius inverters has
to have its own Datamanager and its own IP address.

General information on the ECO series:

This device is equipped with the Datamanager 2.0 by default.
The Datamanager has to be set as a slave in order for communication with the Solar-Log™ to work. The ComCard
connection is a fixed component of the inverter so an additional ComCard is not required. The Light version does
not come with this Datamanager so no settings need to be adjusted here.

«
...
127
128
129
130
131
...
»

Summary of Contents for Solar-Log



























































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Solar-Log

Brand: Geomatics Pages: 16

Brand: YDOC Pages: 45

Brand: Radionode Pages: 53

Brand: Eurochron Pages: 108

Brand: MC Pages: 20

Brand: Huawei Pages: 37

FusionModule 1000A20

Brand: Huawei Pages: 86

Brand: Huawei Pages: 130

FusionModule 1000

Brand: Huawei Pages: 207

SmartLogger1000

Brand: Huawei Pages: 299

SmartLogger3000

Brand: Huawei Pages: 305

FusionModule500

Brand: Huawei Pages: 302

Brand: Huawei Pages: 508

Brand: Agrowtek Pages: 10

Brand: Racelogic Pages: 36

Brand: PowerFleet Pages: 79

EtherSens Oxygen

Brand: process-informatik Pages: 4

Brand: Masibus Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands