background image

236

Q3

67.2 

Q3 12000-14000

Termination

Addressing

Interface

Yes

Yes

RS485

Note 

The same protocol must be selected on both devices In order to ensure correct communication bet-
ween the Solar-Log™ and the inverters.

Protocol selection for device detection:

• 

Q3: Protocol 1

• 

Q3: Protocol 9

The following types are to be connected according to this diagram:

• 

QX12000

• 

QX14000

Overview

• 

Integrated interface

• 

Where to connect: Round pin plug on the outside of the inverter

• 

3-pin wiring

• 

Communication address must be allocated

• 

Inverters must be grounded otherwise this could lead to problems with inverter detection

• 

Installation steps

• 

Switch off the inverters and Solar-Log™

• 

Connect inverters to the Solar-Log™

• 

Connect the inverters to each other

• 

Allocate communication address

Connect inverters to the Solar-Log™

• 

self-made, shielded 3 wire data cable and terminal block connector.

Procedure

1.  If you are making the cable yourself, connect the wires as shown in the following diagram:

Solar-Log™ terminal strip connector

Inverter terminal strip 

Terminal

Terminal

 

1

 

2 - Data +

 

3

 

3 - Ground

 

4

 

4 - Data -

2.  Terminate pin 1 on the terminal block connector and pin 4 on the Solar-Log

TM

 using the 120 

Ω

 terminal resis-

tor.

3.  Terminate on the inverter in accordance with the manufacturer‘s handbook.
4.  Insert the terminal block connector into the Solar-Log™ RS485 socket.

Summary of Contents for Solar-Log



























































































































































































































































































































































































































































































































Reviews: