Solare Datensysteme Solar-Log Components Connection Manual Download | Manualshive

Page: 285 / 506

background image

285

Siemens

Fig.: Siemens – connecting inverters together

Use the SACC-M12MS-4SC connectors supplied with the inverter for data cables.

•

Connect them as shown in the diagram.

•

Connect the bus cable on the last inverter to the RS485 OUT socket using a terminal resistor.

Inverter - RS485 OUT

(4-pin round plug)

Inverter - RS485 IN

(4-pin round plug)

Pin 2

Pin 2

Pin 3

Pin 3

Bus termination

The bus must be terminated on the RS485 OUT connection of the last inverter with 120

Ω

.

To do this use the internal 120

Ω

resistor and wire the following pins in a round 4-pin plug with two jumpers.

Inverter - RS485 OUT (4-pin round plug)

Pin 1

Pin 2

Pin 3

Pin 4

•

Insert this plug into the RS485 OUT socket of the last inverter.

Setting parameters

•

Parameters are set using the display on the inverter.

•

The date and time must be correctly set and the password "72555" entered before the communication set-
tings.

•

The communication parameters are set in the sub-menu
"F1 -> Configuration -> Communication -> RS 485."

•

The individual menu items are selected with the arrow keys

↑↓

and confirmed by pressing ENTER.

•

A consecutive communication address must be allocated to each SINVERT PVM. It is advisable to arrange the
addresses consecutively beginning with 1, i.e. 1, 2, 3 up to a maximum of 31. The Solar-Log™ has address "0".

•

The baud rate should be set to 57600. Baud rate 9600 must only be used when using the wireless package.

«
...
283
284
285
286
287
...
»

Summary of Contents for Solar-Log



























































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Solar-Log

Brand: Watlow Pages: 214

Brand: Lascar Pages: 7

Brand: Egnite Pages: 52

Brand: AST Pages: 12

Brand: Dahua Pages: 24

TruBlue 255 LEVEL

Brand: TE Connectivity Pages: 26

Brand: vendon Pages: 9

Brand: Lascar Electronics Pages: 17

Brand: SS Telecoms Pages: 19

UltraShock Series

Brand: MadgeTech Pages: 2

Brand: MadgeTech Pages: 2

Brand: MadgeTech Pages: 2

Brand: MadgeTech Pages: 2

Brand: ESPEC Pages: 2

Brand: Eddyfi Technologies Pages: 11

3B Netlog 1000541

Brand: 3B SCIENTIFIC PHYSICS Pages: 12

Brand: SATO Pages: 2

Brand: REED Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands