Solare Datensysteme Solar-Log Components Connection Manual Download | Manualshive

Page: 400 / 506

background image

400

Appendix

113.3

Other inverters with Sunspec protocol

(as of firmware 4.2.0)

Even if the manual for a manufacturer does not explicitly have information for the recognition selection via the
Sunspec protocol, it is generally still possible to implement this. „Solar-Log“ has to be selected as the manufacturer
and the „Sunspec“ as the type.

The following interfaces are available: RS485 and Ethernet.

The baud rate has to be explicitly defined. The following selection options are possible:

•

2400

•

4800

•

9600

•

19200

•

57600

•

115200

The wiring depends on the manufacturer and model.
It is important to note the following on the Solar-Log™ RS485 side:

•

1 Data+

•

4 Data+

•

3 GND

Refer to Chapter 1 „Connections“ for more information.

Special inverter instructions, such as activating the Sunspec protocol, are manufacturer specific. (Refer to the
manufacturer‘s manual).

Requirements

Compliance to the Sunspec standard is a basic prerequisite to ensure that communication via the Sunspec proto-
col works. This requirement is usually fulfilled when there is a Sunspec certification for each inverter module (ask
the manufacturer).

►

Sunspec information is available at

http://sunspec.org/download.

In the following list contains the models required (based on the Sunspec specification) to implement data recor-
ding, and active and reactive power control with the Solar-Log™.

Support of the following Sunspec models:

•

Model 1 : Common-Model-Block

•

Manufacturer

•

Serial number

•

Models 101,102,103,111,112 or 113 AC values

•

Yield

•

Uac1-3 (depending on the phases)

•

Iac1-3 (depending on the phases)

•

PAC

•

Temperature

•

Status

•

Error

•

DC values for the missing model 160

«
...
398
399
400
401
402
...
»

Summary of Contents for Solar-Log



























































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Solar-Log

Brand: EA Technology Pages: 35

Brand: Inovonics Pages: 2

Brand: ShockWatch Pages: 3

Brand: TempSen Pages: 2

Brand: FIEDLER Pages: 82

Brand: Xylem Pages: 40

Brand: RBR Pages: 27

Brand: Omni Instruments Pages: 9

Brand: Ebro Pages: 49

Brand: BART Pages: 38

TCD-Download Box/Data

Brand: TachoControl DATA Pages: 13

Brand: Measurement Computing Pages: 32

Brand: T&D Pages: 8

SOMNOwatch plus

Brand: SOMNOmedics Pages: 162

Brand: Sonifex Pages: 66

Brand: Rotronic Pages: 3

RMS MINI LOGGER

Brand: Rotronic Pages: 2

Brand: ELPRO Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands